MAI 2000 System Test Procedure
|
|
MAI 2000 System Test Procedure |
TABLE OF CONTENTS
PARA. TITLE
1.1 PURPOSE
1.2 SCOPE
1.3 REFERENCE DOCUMENTS
1.4 PRECAUTIONARY INSTRUCTIONS
1.5 EQUIPMENT REQUIRED
1.6 SYSTEMS LEVEL TEST FLOW
1.7 TROUBLESHOOTING 2.1 SET CMB JUMPERS & ZERO-OHM PACKS
2.2 SET MEMORY ADDRESS SWITCHES
2.3 SET 4-WAY SWITCHES & JUMPERS
2.4 SET WDD CONTROLLER JUMPERS & SWITCHES
2.5 WDD ADDRESS SETTINGS
2.6 SET LAN SWITCHS
2.7 SET MCS CONTROLLER SWITCHS
2.8 SET SCSI BUS ADAPTER PCBA (1/2" MTS) SWITCHS
3.1 RECORD (VERIFY HI-POT)
3.2 POWERUP, SELFTEST & CONFIG
3.3 INSTALL THE SYSTEM SERIAL NUMBER (SSN)
3.4 INSTALL THE CONFIGURATION RECORD
3.5 VERIFY WD0 BOOT & CONFIGURE THE SYSTEM
3.6 PRINT LABEL
4.1 HOST SETUP
4.2 DIAGNOSTICS
4.3 MINIQ
4.4 FINAL TEST
4.5 CLEAR TEST PROGRAMS
4.6 DELETE TEST CONFIGURATION RECORD
4.7 INSTALL USER SYSTEM SERIAL NUMBER
5.1 WDD FORMATTING & VERIFICATION
5.2 OS INSTALLATION (DISK TO DISK COPY)
5.3 NEW OS (TAPE TO WDD COPY)
5.4 WDD RUNIN
5.5 FLOPPY RUNIN
6.1 OPERATING SYSTEM ERROR CODES
7.1 CHECKLIST
THE PURPOSE OF THIS PROCEDURE IS TO PROVIDE THE INSTRUCTIONS NEEDED TO
PERFORM A COMPLETE AND THOROUGH FUNCTIONAL TEST OF A COMPLETE EAGLE
SYSTEM IN ORDER TO INSURE COMPLIANCE WITH THE SYSTEM REQUIREMENTS.
THIS PROCEDURE DETAILS THREE TYPES OF SYSTEM TESTING AS WELL AS THREE
TYPES OF DISK DRIVE TESTING. THE SYSTEM TESTS CONSIST OF DIAGNOSTIC
TESTS, STAND ALONE SYSTEM EXERCISER AND ON LINE FUNCTIONAL TESTS. THE
DISK TESTS PERTAIN TO THE FLOPPY DISK DRIVES, THE WDD DRIVE 0 WITH OS
INSTALLED AND WDD DRIVE 1. DIAGNOSTICS ARE RUN USING A CENTRALIZED HOST METHOD THAT EMPLOYES A HOST
SYSTEM SUCH AS AN 8000 SERIES MACHINE CONFIGURED FOR MULTI-USER
OPERATION. THIS HOST SYSTEM IS CAPABLE OF DOWNLOADING ALL OF THE
FUNCTIONAL DIAGNOSTIC TESTS NECESSARY TO FULLY TEST THE THE MAI/2000
SYSTEMS. THE HOST WILL INTERFACE THROUGH ITS SERIAL OUTPUT PORTS TO A
LARGE NUMBER OF MAI/2000 SYSTEMS THROUGH THEIR SCC1 PORTS. THIS SCHEME
WILL PROVIDE A METHOD OF AUTOMATICALY TESTING MANY SYSTEMS AT THE SAME
TIME. THE SYSTEM EXERCISER IS RUN UNDER OPERATING SYSTEM CONTROL AND PROVIDES A
STRINGENT TEST FOR THE READING, WRITING AND TRANSFERING OF DATA WITHIN THE
SYSTEM. THIS TEST IS RESIDENT ON THE WDD BUT IS RFEMOVED PRIOR TO SHIPMENT THE FUNCTIONAL TESTS ARE RUN AS A FINAL CHECK OF THE SYSTEMS UNDER A
TYPICAL END USER ENVIRONMENT. THE DISK TESTS CHECK THE DISK DRIVES IN A SYSTEM SETTING AND VERIFY THEIR
FUNCTIONALITY.
TE10-00003 2000 SERIES TEST PLAN
514008 SCC DESK TOP COMPUTER
515008 SCS DESK TOP COMPUTER
514108 PSC DESK TOP COMPUTER
515108 MAD DESK TOP COMPUTER
502046 SYSTEM SPEC DESK TOP COMPUTER
011144 EAGLE UTILITY FUNCTIONAL SPEC
011186 DIAGNOSTIC EXECUTIVE
011214 DEBUGGER
ALL POWER MUST BE OFF WHENEVER A PCBA OR CABLE IS INSERTED OR EXTRACTED
FROM A CONNECTOR, OTHERWISE DAMAGE TO THE PROCESSOR, PERIPHERALS OR OTHER
ASSOCIATED EQUIPMENT MAY RESULT.
IT IS IMPORTANT THAT ALL CABLES AND CONNECTORS ARE PROPERLY IDENTIFIED
AND CONNECTED CORRECTLY PRIOR TO APPLYING POWER, OTHERWISE ERRONEOUS
INDICATIONS OR EVEN DAMAGE COULD RESULT. FLOPPY DISKETTES ARE FRAGILE AND REQUIRE CAREFUL HANDLING. THE DISKETTES
ARE SEALED IN PROTECTIVE COVERS THAT SHOULD NEVER BE REMOVED. ACCESS
OPENINGS IN THE COVERS EXPOSE THE DISKETTE. THESE EXPOSED SURFACES MUST
NOT BE TOUCHED, OTHERWISE DAMAGE TO THE PROGRAMMED INFORMATION COULD
RESULT.
AN EAGLE COMPATABLE VIDEO TERMINALS WITH MATING CABLES.
A FLOPPY DISK DRIVE WITH MATING CABLE.
A SET OF EAGLE DIAGNOSTIC DISKETTES.
AN 8000 TYPE SYSTEM WITH MULTIPLE SERIAL PORTS AND
INTERFACE CABLES. (ONE ONLY)
A PARALLEL PORT LOOPBACK CONNECTOR.
A PARALLEL PRINTER WITH MATTING CABLE (ONE ONLY)
A SERIAL PRINTER WITH MATTING CABLE (ONE ONLY)
THIS FLOW CHART SHOWS EACH ASSEMBLY AND TEST STATION ON THE SERIES 2000
PRODUCTION LINE. THE ASSEMBLY STEPS HAVE BEEN OMITTED AND ARE COVERED
UNDER MANUFACTURING ENGINEERING DOCUMENTATION AND ONLY THE STEPS RELATING
TO TEST ARE SHOWN. EACH TEST STEP LISTS THE SECTION NUMBER OF THIS
PROCEDURE THAT MUST BE FOLLOWED TO PERFORM THAT PARTICULAR TEST.
SYSTEMS MAY BE SHIPPED WITH OR WITHOUT A WINCHESTER DISK DRIVE 0
INSTALLED, DEPENDING ON SCHEDULE REQUIREMENTS. THE TESTING OF THE SYSTEMS
WILL BE THE SAME IN EITHER CASE. THE ONLY DIFFERENCE FOR A SYSTEM WITHOUT
A DRIVE 0 IS THAT THE DISK DRIVE WILL BE REMOVED FROM THE SYSTEM AND
PACKAGED SEPARATELY AFTER COMPLETION OF ALL TESTING. SPECIAL TEST PROGRAMS WILL BE RESIDENT ON THE OPERATING SYSTEM SOFTWARE.
THESE PROGRAMS, HOWEVER, MUST BE REMOVED FROM THE DISK DRIVES PRIOR TO
SHIPMENT. A LISTING OF THE NAMES AND FUNCTIONS OF THESE TEST PROGRAMS CAN
BE FOUND BY TYPING "list" ON ANY SYSTEM WITH A WDD 0 INSTALLED.
TEST FLOW CHART
---------------
SECT. 2.0 ---------- ----------
SYSTEM CONFIGURATION | | | |
| SYSTEM | | DISK |
| ASSEMBLY | | SUB-ASSY |
| | | |
---------- ----------
| |
| |
| |
SECT. 3.0 _____V____ _____V____ SECT. 5.0
PRE-TEST | | | | DRIVES
| PRE-TEST |<-- |FORMATTING|
| | || |
---------- | ----------
| | |
| | |
| | |
| | V
| | / \
| | / \
SECT. 4.0 _____V____ |___
RUNIN & FINAL TEST | | WDD 0 \ /
| RUNIN | \ /
| | |
---------- WDD 1 |
| & |
| FLOPPY | FLOPPY DRIVE
_____V____ _____V____ -----------------
| | | | 5.5 RUNIN
| PRE-SHIP | | KIT |
| | | |
__________ __________
| |
_____V____ _____V____
| | | |
| SHIP | | SHIP |
| | | |
---------- ----------
TROUBLESHOOTING, BY ITS VERY NATURE, CANNOT BE "PROCEDUREIZED". IT
REQUIRES SKILL, TRAINING, FAMILIARITY WITH THE EQUIPMENT AND A SPECIAL
APTITUDE. THIS SECTION, THEN, WILL ONLY DEAL WITH THE ROUTING OF FAILED
EQUIPMENT.
A) PCBA'S THAT FAIL AT THE FUNCTIONAL TEST LEVEL WILL BE RESUBMITTED TO
ATE TESTING. IF PROBLEMS ARE FOUND, THE APPROPRAITE CORRECTIVE ACTION
WILL BE TAKEN AND THE PCBA WILL CONTINUE ITS NORMAL FLOW FROM THAT
POINT.
B) PCBA'S THAT FAIL FUNCTIONAL TESTING AND PASS ATE RETESTING WILL BE
SUBMITTED FOR TESTING ON THE FLOPPY BASSED DIAGNOSTIC SYSTEM WHERE
SPECIFIC TESTS CAN BE SELECTED TO AID IN PIN-POINTING THE PROBLEM
C) FAILED PCBA'S WILL BE PROPERLY IDENTIFIED SO THAT TRACEABILITY CAN BE
MAINTAINED. THIS IS NECESSARY FOR RECORD KEEPING AND ALSO TO PRECLUDE
PCBA'S FROM BEING TRAPPED IN AN ENDLESS ATE/FUNCTIONAL FLOW LOOP.
D) FAILURE DATA MUST BE RECORDED AND REVIEWED SO THAT ANY WEAKNESSES OR
GAPS IN THE TESTING CAN BE FOUND AND CORRECTED.
EACH SYSTEM MUST BE PROPERLY CONFIGURED PRIOR TO TEST. THE FOLLOWING
TABLES SHOW THE PROPER SETTINGS TO ACCOMPLISH THIS.
2ND ARTWORK CMB | 3RD ARTWORK CMB
--------------- | ---------------
|
JMP A 1 TO 3 | JMP A PIN 9 OF ZERO-OHM PACK
JMP A 2 TO 4 | TO PIN 1 OF SOCKET A
JMP A 5 TO 6 | -----------
JMP A 7 TO 9 | ] |
JMP A 8 TO 10 | -----------
JMP A 11 TO 13 | ^ TERM/PRNTR
JMP A 12 TO 14 | JMP B PIN 9 OF ZERO-OHM PACK
JMP B 1 TO 3 | TO PIN 1 OF SOCKET B
JMP B 2 TO 4 | -----------
JMP B 5 TO 6 | ] |
JMP B 7 TO 9 | -----------
JMP B 8 TO 10 | ^ TERM/PRNTR
JMP B 13 TO 15 | JMP C NC
JMP B 14 TO 16 | JMP D 2 T0 3
JMP C NC | JMP E 1 TO 2
JMP D 2 T0 3 | JMP E 7 TO 8
JMP E 1 TO 2 | JMP F 1 TO 2
JMP E 7 TO 8 | JMP G NC
JMP F 1 TO 2 | JMP H NC
JMP G 15 TO 16 | JMP K PIN 1 OF ZERO-OHM PACK
JMP G 17 TO 18 | TO PIN 1 OF SOCKET K
JMP G 19 TO 20 | -----------
JMP G 23 TO 24 | RS232 | [
JMP H NC | -----------
JMP K 1 TO 2 | JMP L 1 TO 2
JMP L 1 TO 2 | JMP M 1 TO 2
JMP M 1 TO 2 | JMP N 1 TO 2
JMP N 1 TO 2 | JMP P NC
JMP P NC | JMP R NC
JMP R NC | JMP S NC
JMP S NC | JMP T 2 TO 3
* JMP S1 1 TO 2 | JMP V 1 TO 2
| JMP W NC
| JMP X NC
| * JMP S1 1 TO 2
*CAUTION*
1 2 3 <-- NUMBERED DIFFERENT --> 3 2 1
_______ | _______
| o o o | | | o o o |
CMB-->======================= | =======================<--CMB
JMP S1 | JMP S1
VIEWED FROM REAR OF CMB | VIEWED FROM REAR OF CMB
REVISION 'A' & 'X3' ARTWORKS ONLY
|BOARD # | MEMORY ADDRESS | SWITCH POSITION |
| | FROM | TO | 1 | 2 | 3 | 4 | 5 | 6 |
|--------|--------|--------|---|---|---|---|---|---|
| 1 | 00000 | 3FFFF | X | X | X | X | X | X |
|--------|--------|--------|---|---|---|---|---|---|
| 2 | 40000 | 7FFFF | X | X | X | X | X | |
X=ON |--------|--------|--------|---|---|---|---|---|---|
POSITION | 3 | 80000 | BFFFF | X | X | X | X | | X |
|--------|--------|--------|---|---|---|---|---|---|
| 4 | C0000 | FFFFF | X | X | X | X | | |
|--------|--------|--------|---|---|---|---|---|---|
| 5 | 100000 | 13FFFF | X | X | X | | X | X |
|--------|--------|--------|---|---|---|---|---|---|
| 6 | 140000 | 17FFFF | X | X | X | | X | |
REVISION 'X2' ARTWORK ONLY
|BOARD # | MEMORY ADDRESS | SWITCH POSITION |
| | FROM | TO | 1 | 2 | 3 | 4 | 5 | 6 |
|--------|--------|--------|---|---|---|---|---|---|
| 1 | 00000 | 3FFFF | X | X | X | X | X | X |
|--------|--------|--------|---|---|---|---|---|---|
| 2 | 40000 | 7FFFF | X | X | X | X | X | |
X=ON |--------|--------|--------|---|---|---|---|---|---|
POSITION | 3 | 80000 | BFFFF | X | X | | X | X | X |
|--------|--------|--------|---|---|---|---|---|---|
| 4 | C0000 | FFFFF | X | X | | X | X | |
|--------|--------|--------|---|---|---|---|---|---|
| 5 | 100000 | 13FFFF | X | X | X | X | | X |
SW1 POSITION
X=ON | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |10 |
POSITION |---|---|---|---|---|---|---|---|---|---|
| X | | | | | | | X | | X | BOARD 1
SETTINGS |---|---|---|---|---|---|---|---|---|---|
FOR BOTH | X | | | X | | | | X | | | BOARD 2
904741 & |---|---|---|---|---|---|---|---|---|---|
904943 | X | | | X | X | | | | X | X | BOARD 3
|---|---|---|---|---|---|---|---|---|---|
| X | | | X | X | X | | | X | | BOARD 4
JUMPERS FOR 904741 PCB JUMPERS FOR 904943 PCB
PGM 1-4 1 TO 7 PGM 1-4 1 TO 3
PGM 1-4 2 TO 8 PGM 1-4 2 TO 4
PGM 1-4 3 TO 4 PGM 1-4 5 TO 6
PGM 1-4 9 TO 10 PGM 1-4 7 TO 8
PGM 1-4 13 TO 15 PGM 1-4 9 TO 11
PGM 1-4 14 TO 16 PGM 1-4 10 TO 12
PGM 1-4 13 TO 15
PGM 1-4 14 TO 16
ON BOARD #1 (903496-001) ON BOARD #2 (903496-002)
CONNECT JUMPER AT JMP A CONNECT JUMPER AT JMP A
FROM 1 TO 2 AS SHOWN: FROM 2 TO 3 AS SHOWN:
------------------- -------------------
| --------- | | --------- |
| | O O | O | | O | O O | |
| --------- | | --------- |
------------------- -------------------
1 2 3 1 2 3
DRIVE 0 -----------------
ON 903496-001 | --- | SET JMP B & JMP C TO MATCH
OR | | O | O O | 1 THE DRIVE TYPES INSTALLED.
DRIVE 2 JMP B | | | | (IN THE SAMPLE SHOWN, DRIVE 0
ON 903496-002 | | O | O O | 2 OR 2 IS SET FOR A MAXTOR OR A
| --- | MICROPOLIS AND DRIVE 1 OR 3
|-----------------| IS SET FOR A RODIME.
DRIVE 1 | --- |
ON 903496-001 | O | O | O | 1
OR JMP C | | | |
DRIVE 3 | O | O | O | 2
ON 903496-002 | --- |
-----------------
A B C
^ ^ ^
| | |
| | ---------- NOT USED
| |
MAXTOR & MICROPOLIS DRIVES -- --------------- RODIME DRIVES
TO SET THE o o o o o o
RODIME DRIVES, ___ ___ ___ ___ ___ ___ ___ ___
PLACE PINS IN | | | | | | | o | | | | | | o | | |
THE HOOKS AS | | | | | | | |
SHOWN | | | | | | | |
------------------------- -------------------------
DRIVES 0 SETTING DRIVES 1 SETTING
______________________ ______________________ TO SET THE | | | | ---- | | | ---- | MAXTOR DRIVES, | | | | | | | | | | | | PLACE JUMPERS | | | | ---- | | | ---- | AS SHOWN | | | | | | | | | | | |
DRIVES 0 SETTING DRIVES 1 SETTING
TO SET THE MICROPOLIS DRIVES, PLACE JUMPERS AS SHOWN BELOW:
_ _ _ _ _ _
TO SET THE | | | | || || | | | | | | | || |
MICROPOLIS | | | | || || | | | | | | | || |
DRIVES, PLACE | | | |_||_||_| | | |_| | |_||_|
THE JUMPERS | | | | | | | | | | | |
AS SHOWN ---------------------- ----------------------
DRIVES 0 SETTING DRIVES 1 SETTING
NOTE: WHEN MORE THAN ONE DRIVE IS CONNECTED TO ANY CONTROLLER, ONLY THE
DRIVE CONNECTED AT THE END OF THE COMMON BUS CABLE SHOULD HAVE A
TERMINATOR INSTALLED. THE DRIVE CONNECTED AT THE INTERMEDIATE
POINT OF THE BUS CABLE MUST HAVE ITS TERMINATOR REMOVED.
SW POSITION
X=ON POSITION | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
|---|---|---|---|---|---|---|---|
| | | | | | | | | SW1 OF LAN UNDER TEST
|---|---|---|---|---|---|---|---|
| | | | X | X | | | X | SW2 OF LAN UNDER TEST
|---|---|---|---|---|---|---|---|
| X | | | | | | | X | SW1 OF CAPTIVE LAN
|---|---|---|---|---|---|---|---|
| | | | X | X | | X | | SW2 OF CAPTIVE LAN
SW1 POSITION
X=ON POSITION | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
|---|---|---|---|---|---|---|---|
| X | X | X | X | | | | X |
SW1 POSITION X=ON POSITION | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
|---|---|---|---|---|---|---|---|
| X | X | X | X | X | X | X | X |
FROM THE CHECKLIST THAT FOLLOWS, PERFORM EACH TEST LISTED. FOR THE
SPECIFIC PROCEDURE REFER TO THE SECTION NUMBER SHOWN IN THE CHECKLIST.
PERFORMING THE TESTS IN THE ORDER SHOWN IS DESIREABLE BUT NOT MANDATORY,
HOWEVER, THE PROCEDURE IS WRITTEN ASSUMING PERFORMANCE IN SEQUENTIAL
ORDER. ============= CHECKLIST ==================
| | | |
# | TEST | DESCRIPTION | REQUIRED | SECT#
====================================================================
1 | HI-POT VERIFICATION | VERIFY HI-POT | EVERY SYSTEM | 3.1
--------------------------------------------------------------------
2 | POWERUP, SELFTEST | SELFTEST & | EVERY SYSTEM | 3.2
| & CONFIG | SET WD0 AS DEFAULT| |
--------------------------------------------------------------------
3 | INSTALL SSN | ONTO NVRAM | EVERY SYSTEM | 3.3
--------------------------------------------------------------------
4 | INSTALL THE | CONFIG RECORD | ONLY IF | 3.4
| CONFIGURATION RECORD| MUST MATCH SSN | AVAILABLE |
--------------------------------------------------------------------
5 | VERIFY WD0 BOOT | VERIFICATION & | EVERY SYSTEM | 3.5
| & CONFIGURE SYSTEM | CONFIGURATION | |
--------------------------------------------------------------------
6 | PRINT LABEL | FOR SHIPPING BOX | AS REQUIRED | 3.6
--------------------------------------------------------------------
A VERIFICATION OF COMPLETION OF THE HI-POT TEST MUST BE PERFORMED ON
EVERY 2000 SYSTEM. A LOG SHOWING THIS 1S REQUIRED FOR UL COMPLIANCE.
3.1.1 PRIOR TO POWER BEING APPLIED TO ANY 2000 SYSTEM, THE TEST
OPERATOR WILL VERIFY THAT A HI-POT TEST LABEL IS ATTACHED TO
THE REAR PANEL OF THE POWER SUPPLY ASSEMBLY.
3.1.2 UPON VERIFICATION, THE TEST OPERATOR WILL RECORD IN THE HI-POT
VERIFICATION LOG THE CPU SERIAL #, THE POWER SUPPLY SERIAL #,
THE DATE VERIFIED AND THE VERIFYING TEST OPERATOR'S NAME.
3.1.3 ANY POWER SUPPLY WITHOUT A HI-POT TEST LABEL SHALL BE REMOVED
FROM ITS SYSTEM AND REJECTED.
3.1.4 A SAMPLE OF THE LOG TO BE USED IS SHOWN BELOW:
-------------------------------------------------------------------
| |
| ***** VERIFICATION LOG ***** |
| |
| EAGLE POWER SUPPLY HI-POT & GROUND CONTINUITY |
| |
| |
| | EAGLE CPU | POWER SUPPLY | DATE | TEST | |
| | SERIAL # | SERIAL # | VERIFIED | OPERATOR | |
| |==========================================================| |
| | | | | | |
| |----------------------------------------------------------| |
| | | | | | |
| |----------------------------------------------------------| |
| | | | | | |
| |----------------------------------------------------------| |
| | | | | | |
| |----------------------------------------------------------| |
---------------------------------------------------------------------
THIS SECTION DEALS WITH INITIAL POWER-UP, SYSTEM SELFTEST AND
PROGRAMING THE DEFAULT BOOT DEVICE.
3.2.1 VERIFY THAT THE SYSTEM TO BE TESTED HAS BEEN PROPERLY
CONFIGURED PER ITS FACTORY ORDER.
3.2.2 CONNECT A VIDEO TERMINAL TO THE SYSTEM'S SCC0 PORT.
3.2.3 VERIFY THE SYSTEM POWER REQUIREMENTS AND CONNECT THE SYSTEM TO
AN APPROPRAITE POWER RECEPTACLE.
3.2.4 PLACE THE SYSTEM POWER SWITCH IN THE ON POSITION.
3.2.5 DEPRESS THE ESCAPE KEY REPEATEDLY.
3.2.6 WHEN <DEBUG> IS DISPLAYED, TYPE "CONFIG" AND <CR>.
3.2.7 WHEN THE CONFIG MENU IS DISPLAYED, TYPE "RE" AND >CR>.
3.2.8 WHEN <CONFIG> IS DISPLAYED, TYPE "DI" AND <CR> TO DISPLAY THE
HARDWARE CONFIGURATION.
3.2.9 VERIFY THAT CONFIGURATION DISPLAYED MATCHES THE CONFIGURATION
SHOWN BELOW. ******************************************************************************
* *
* term type : evdt *
* boot port : wd0 *
* console port : sc0 baud:9600 data bits:7 stop bits:1 parity:odd flow:xon *
* download port : sc1 baud:9600 data bits:7 stop bits:1 parity:odd flow:xon *
* printer port : pit0 *
* *
******************************************************************************
3.2.10 IF ANY LINE DOES NOT MATCH, CHANGE ONLY THAT LINE AS DESCRIBED
IN THE INSTRUCTIONS BELOW.
TERM TYPE
A. WHEN <CONFIG> IS DISPLAYED, TYPE "T" AND <CR>.
B. WHEN "TERMINAL TYPE:" IS DISPLAYED, TYPE "EVDT" AND >CR>. BOOT PORT
A. WHEN <CONFIG> IS DISPLAYED, TYPE "B" AND <CR>.
B. WHEN "BOOT DEVICE:" IS DISPLAYED, TYPE "WD" AND <CR>.
C. WHEN "BOOT UNIT:" IS DISPLAYED, TYPE "0" AND <CR>. CONSOLE PORT
A. WHEN <CONFIG> IS DISPLAYED, TYPE "C" AND <CR>.
B. WHEN "CONSOLE DEVICE:" IS DISPLAYED, TYPE "SC" AND <CR>.
C. WHEN "CONSOLE UNIT:" IS DISPLAYED, TYPE "0" AND <CR>.
D. WHEN "CONSOLE BAUD:" IS DISPLAYED, TYPE "9600" AND <CR>.
E. WHEN "DATA BITS:" IS DISPLAYED, TYPE "7" AND <CR>.
F. WHEN "STOP BITS:" IS DISPLAYED, TYPE "1" AND <CR>.
G. WHEN "PARITY:" IS DISPLAYED, TYPE "ODD" AND <CR>.
H. WHEN "FLOW:" IS DISPLAYED, TYPE "XON" AND <CR>. DOWDLOAD PORT
A. WHEN <CONFIG> IS DISPLAYED, TYPE "D" AND <CR>.
B. WHEN "DOWNLOAD DEVICE:" IS DISPLAYED, TYPE "SC" AND <CR>.
C. WHEN "DOWNLOAD UNIT:" IS DISPLAYED, TYPE "1" AND <CR>.
D. WHEN "DOWNLOAD BAUD:" IS DISPLAYED, TYPE "9600" AND <CR>.
E. WHEN "DATA BITS:" IS DISPLAYED, TYPE "7" AND <CR>.
F. WHEN "STOP BITS:" IS DISPLAYED, TYPE "1" AND <CR>.
G. WHEN "PARITY:" IS DISPLAYED, TYPE "ODD" AND <CR>.
H. WHEN "FLOW:" IS DISPLAYED, TYPE "XON" AND <CR>. PRINTER PORT
A. WHEN <CONFIG> IS DISPLAYED, TYPE "P" AND <CR>.
B. WHEN "PRINTER PORT:" IS DISPLAYED, TYPE "PIT" AND <CR>. 3.2.11 WHEN ALL NECESSARY CHANGES HAVE BEEN MADE, TYPE "WRITE" AND
<CR> TO SAVE THESE CHANGES.
3.2.12 WHEN THE DIRECTORY IS DISPLAYED, VERIFY THAT THE CORRECT DATA
HAS BEEN WRITTEN. THEN TYPE "Y" AND <CR>.
3.2.13 WHEN "NVRAM COMPLETE" IS DISPLAYED, RESET THE SYSTEM AND VERIFY
THAT THE CONSOLE TERMINAL DISPLAYS THE SYSTEM SELF TEST
INFORMATION. VERIFY THAT ALL ITEMS LISTED SHOW A "PASS"
INDICATION AND THAT THERE ARE NO FAILURES.
3.2.14 VERIFY THAT THE CONFIGURATION DISPLAYED ON THE SELF-TEST IS
CORRECT AND MATCH THE FACTORY ORDER CONFIGURATION. NOTE: SINCE
A DISK DRIVE HAS NOT BEEN INSTALLED IN THE SYSTEM YET, THE
SYSTEM WILL NOT BOOT AT THIS POINT.
3.2.15 TURN OFF THE SYSTEM POWER.
3.3.1 REMOVE THE SOCKETED INTEGRATED CIRCUIT AT LOCATION 8Z ON THE
CMB AND REPLACE IT WITH THE "SSN TEST IC".
3.3.2 INSTALL AN "SSN" TAPE INTO THE STREAMER TAPE DRIVE.
3.3.3 TURN ON THE SYSTEM POWER AND PRESS THE CONTROL AND "C" KEYS
TOGETHER TO SELECT ALTERNATE-LOAD.
3.3.4 WHEN PROMPTED "BOOT DEVICE:", TYPE "cs" AND <CR>.
3.3.5 WHEN PROMPTED "SYSTEM FILE:", TYPE "ssn" AND <CR>.
3.3.6 THE TERMINAL WILL DISPLAY "BOOTING FROM CS0......." AND THEN
"BOOT COMPLETE" AND THE EXISTING SYSTEM SERIAL NUMBER.
3.3.7 WHEN PROMPTED "NEW SERIAL NUMBER: 2", TYPE IN THE NEW SSN IN
THE FORM "000-90XXX FOLLOWED BY A <CR>.
3.3.8 WHEN THE INSTALLATION IS COMPLETE POWER DOWN THE SYSTEM.
3.3.9 WHEN THE SYSTEM POWER IS OFF, REPLACE THE ORIGINAL IC AT
LOCATION 8Z ON THE CMB. * * DO NOT SHIP THE SECURITY IC * *
3.3.10 TURN ON THE SYSTEM AND OBSERVE THE SELF-TEST TO VERIFY THAT THE
SYSTEM SERIAL NUMBER DISPLAYED IS CORRECT.
3.4.1 INSTALL THE OS TAPE CARTRIDGE INTO THE TAPE DRIVE AND TURN ON
THE SYSTEM POWER.
3.4.2 WHEN THE SYSTEM DISPLAYS THE SELF-TEST, SELECT ALTERNATE-LOAD
BY PRESSING THE CONTROL AND "C" KEYS TOGETHER.
3.4.3 WHEN PROMPTED "BOOT DEVICE:", TYPE "CS" AND <CR>.
3.4.4 WHEN PROMPTED "SYSTEM FILE:", DEPRESS THE <CR>.
3.4.5 VERIFY THAT THE SYSTEM LOADS FROM THE STREAMER AND THAT THE
TERMINAL DISPLAYS THE FOLLOWING:
******************************************************
* *
* BOOTING FROM CS0 *
* LOADING OPERATING SYSTEM *
* ............................................. *
* ............................................. *
* ............... *
* LOADING CONFIGURATION FILE *
* . *
* LOADING RAMDISK *
* ............................................. *
* ............................................. *
* ............... *
* EXECUTING *
* *
* *** INSTALLATION SYSTEM LOAD COMPLETE! *** *
* *
* THIS INSTALLATION SYSTEM WILL BE USED TO PERFOM *
* ONE OF THREE FUNCTIONS. ----------------------- *
* ----------------------------------------- SELET *
* THE DESIRED OPTION AND TYPE THE CORRESPONDING *
* LETTER FOLLOWED BY THE 'RETURN' KEY. *
* *
* A - CREATE DEFAULT PARTITIONS *
* *
* B - PRESERVE CURRENT PARTITIONS *
* *
* C - RESTORE LOADER TO WINCHESTER DISK *
* *
* D - INSTALL CONFIGURATION RECORD *
* *
* E - REDISPLAY THIS SCREEN *
* *
* <CTL-D>, 'shutdown' - REBOOT THE SYSTEM *
* *
* OPTION> *
******************************************************
3.4.6 WHEN PROMPTED <OPTION>, TYPE "d" AND <CR>.
3.4.7 WHEN PROMPTED "INSERT CONFIGURATION TAPE, PRES RETURN.....",
INSERT THE TAPE AND PRESS <CR>.
3.4.8 THE TAPE SHOULD RUN AND THEN THE DISPLAY SHOULD BE AS FOLLOWS: ******************************************************
* CAUTION: FILES ON THIS TAPE ARE............ *
* ....................MATCH ORIGINAL OWNERS.*
* NUMBER OF FILES RESTORED: 1 *
* CONFIGURATION RECORD INFO (/sys/config.2000-9XXXX *
* USER SSN.........................2000-9XXXX *
* SYSTEM NAME......................010/SYSTEMS TEST *
* SYSTEM TYPE......................XXXX *
* " *
* " *
* WRITING NEW CONFIGURATION *
* PROCEDURE COMPLETE. <CTL-D> 'shutdown' TO REBOOT *
* *
* OPTION> *
****************************************************** 3.4.9 WHEN PROMPTED "OPTION>", REMOVE THE CONFIGURATION TAPE AND
DEPRESS THE CONTROL AND D KEYS TOGETHER.
3.4.10 WHEN PROMPTED "SINGLE, MULTI, OR SHUTDOWN", TYPE "shutdown"
AND <CR>.
3.5.1 VERIFY THAT THE DISK CONTROLLER JUMPERS ARE CONFIGURED TO MATCH
TYPE OF DISK THAT IS INSTALLED. (SEE SECT 2.)
3.5.2 TURN ON THE SYSTEM POWER.
3.5.3 VERIFY THAT THE SYSTEM SELF-TEST IS DISPLAYED AND THAT THERE
ARE NO FAILURES.
3.5.4 VERIFY THAT THE SYSTEM BOOTS FROM WD0.
3.5.5 WHEN PROMPTED "UPDATE CLOCK", UPDATE THE SYSTEM DATE AND TIME.
3.5.6 WHEN PROMPTED <ADMIN>, DEPRESS THE CONTROL AND D KEYS TOGETHER.
3.5.7 WHEN PROMPTED "SINGLE, MULTI OR SHUTDOWN", TYPE "multi" AND
<CR>.
3.5.8 VERIFY THAT THE SYSTEM ADVANCES TO MULTI USER MODE AND DISPLAYS
THE MAI/2000 LOGO.
3.5.9 WHEN PROMPTED "ACCOUNT NAME", TYPE "admin" AND <CR>.
3.5.10 WHEN PROMPTED <ADMIN>, TYPE "shutdown 0" AND <CR>. VERIFY THAT
THE SYSTEM DISPLAYS SHUTTING DOWN IN 15 SECONDS AND ADVANCES TO
SINGLE USER MODE.
3.5.11 WHEN PROMPTED <ADMIN>, TYPE "init" AND <CR>.
3.5.12 AT THE MENU, TYPE "1" AND <CR> TO SELECT EAGLE SYSTEMS.
3.5.13 WHEN PROMPTED TO ENTER THE NUMBER OF MEMORY BOARDS PRESENT,
TYPE IN THE NUMBER OF MEMORY BOARDS CONFIGURED IN THAT SYSTEM.
3.5.14 WHEN PROMPTED <ADMIN>, TYPE "configure" AND <CR>.
3.5.15 THE 'CONFIGURATION' MENU WILL BE DISPLAYED. FOLLOW
THE INSTRUCTIONS IN THE MENU TO CONFIGURE ALL AVAILABLE PORTS.
3.5.16 WHEN THE RECONFIGURING HAS BEEN COMPLETED, EXIT THE 'CONFIGURE'
MENU BY PRESSING <CR>.
3.5.17 WHEN PROMPTED <ADMIN>, DEPRESS THE CONTROL AND D KEYS TOGETHER.
3.5.18 WHEN PROMPTED "SINGLE, MULTI OR SHUTDOWN", TYPE "shutdown" AND
<CR>.
3.5.19 WHEN THE SYSTEM HAS SHUTDOWN, POWER DOWN THE SYSTEM.
3.6.1 CONNECT AN 80 COLUMN PRINTER TO THE CMB'S SCC1 PORT.
3.6.2 TURN ON THE SYSTEM POWER.
3.6.3 VERIFY THAT THE SYSTEM SELF-TEST IS DISPLAYED AND THAT THERE
ARE NO FAILURES.
3.6.4 VERIFY THAT THE SYSTEM BOOTS FROM WD0.
3.6.5 WHEN PROMPTED "UPDATE CLOCK" DEPRESS <CR>.
3.6.6 WHEN PROMPTED <ADMIN>, TYPE "label" AND <CR>.
3.6.7 AT THE INITIAL MENU, SELECT EAGLE SYSTEM LABELS.
3.6.8 AT THE FOLLOWING MENU, SELECT THE TYPE OF LABEL NEEDED. THE
OPTIONS ARE: SYSTEMS WITH NO WDD 0, DRIVE KITS OR SYSTEMS WITH
WDD 0 & OS.
3.6.9 ENTER THE INFORMATION REQUESTED AT THE MENU PROMPTS UNTIL ALL
THE DATA HAS BEEN INPUTTED.
3.6.10 AT THE "LABEL VERIFY, PRINT & EDIT" MENU, SELECT "VERIFY" AND
CHECK THAT ALL THE INFORMATION DISPLAYED MATCHES THE SYSTEM
UNDER TEST THEN PRESS THE <CR> TO CONTINUE.
3.6.11 IF THE LABEL IS NOT CORRECT, SELECT "EDIT" AND FOLLOW THE MENU
INSTRUCTIONS.
3.6.12 WHEN ALL INFORMATION IS CORRECT, SELECT "PRINT" TO PRINT THE
LABEL.
3.6.13 WHEN THE LABEL HAS BEEN PRINTED, SELECT "RETURN TO THE BEGINING
TO PRINT ADDITIONAL LABELS OR SELECT "LABEL COMPLETE" TO RETURN
TO THE COMMAND INTERPRETER.
3.6.14 WHEN PROMPTED <ADMIN>, DEPRESS THE CONTROL AND D KEYS TOGETHER.
3.6.15 WHEN PROMPTED "SINGLE, MULTI OR SHUTDOWN", TYPE "shutdown" AND
<CR>.
3.6.16 WHEN THE SYSTEM IS SHUTDOWN, POWER DOWN THE SYSTEM.
FROM THE CHECKLIST THAT FOLLOWS, PERFORM EACH TEST LISTED. FOR THE
SPECIFIC PROCEDURE REFER TO THE SECTION NUMBER SHOWN IN THE CHECKLIST.
A MINIMUM OF 20 HOURS TOTAL TEST TIME IS REQUIRED FOR EVERY SYSTEM. THIS
TOTAL INCLUDES THE TIME IN PRE-TEST, FINAL TEST, DIAGNOSTICS AND MINIQ.
ONCE THE INDIVIDUAL TEST TIME REQUIREMENTS SHOWN IN THE CHECKLIST BELOW
HAVE BEEN MET, THE BALANCE OF THE TOTAL REQUIREMENT MAY BE SATISIFIED BY
RUNNING EITHER DIAGNOSTICS OR MINIQ.
A MINIMUM OF 10% OF THE SYSTEMS BUILT EACH WEEK MUST RUN MINIQ FOR 60
HOURS MINIMUM. (EXAMPLE 8PM FRI. TO 8AM MON.). DATA FROM THIS SAMPLE
SHALL BE MONITORED AND USED AS AN INDICATOR TO VERIFY THE EFFECTIVITY OF
THE REQUIRED TEST DURATION.
CHECKLIST # | TEST | DESCRIPTION | REQUIRED | SECT#
========= ===================================================================
1 | HOST SETUP | INITIAL SETUP | AS NEEDED | 4.1
-------------------------------------------------------------------
2 | DIAGNOSTICS | MEMORY | 6 HRS. MIN. | 4.2
| | NVRAM | |
| | MMU | |
| | CMB | |
| | PIT W/LOOPBACK | |
-------------------------------------------------------------------
2A| ALTERNATE METHOD | AUTO & SIT | 6 HRS. MIN. | 4.2A
| DIAGNOSTICS | | |
-------------------------------------------------------------------
3 | MINIQ | OS BASED EXERCISER| 12 HRS. MIN. | 4.3
-------------------------------------------------------------------
4 | FINAL TESTS | FUNCTIONAL TESTS | TEST EVERY | 4.4
| | OF ALL PORTS | CONTROLLER & |
| | AND SUBSYSTEMS | PORT PRESENT |
-------------------------------------------------------------------
5 | CLEAR TEST PROGRAMS | CAN'T SHIP MFG | VERIFY TESTS | 4.5
| | TEST PROGRAMS | COMPLETED |
-------------------------------------------------------------------
6 | DELETE TEST | CAN'T SHIP MFG | IF NO USER'S | 4.6
| CONFIGURATION RECORD| TEST CONFIG RECORD| CONFIG RECORD|
-------------------------------------------------------------------
7 | INSTALL USER'S SSN | INSTALL TO NVRAM | IF NO USER'S | 4.7
| | | SSN IN YET |
-------------------------------------------------------------------
4.1.1 VERIFY THAT THE HOST SYSTEM IS READY TO RUN. (REFER TO THE
HOST SYSTEM MANUAL FOR INSTRUCTIONS).
4.1.2 VERIFY THAT THERE ARE NO CABLES CONNECTED TO ANY OF THE EAGLE
SYSTEMS. IF THERE ARE, DISCONNECT THEM.
4.1.3 VERIFY THAT THE HOST HAS A CABLE CONNECTED TO EVERY 8-WAY AND
4-WAY PORT. IF NOT, INSTALL A PLUG JUMPER ACROSS THE TOP TWO
PINS OF EACH UNCONNECTED PORT.
4.1.4 PLACE ALL FOUR SENSE SWITCHES (LOCATED ON THE MCS PCBA) IN THE
DOWN POSITION IF DISK DRIVE 0 (FIXED DISK) IS DESIRED. IF DISK
DRIVE 1 (REMOVABLE DISK) IS THE DRIVE DESIRED, PLACE THE
SECOND SENSE SWITCH FROM THE BOTTOM IN THE UP POSITION AND
PLACE THE OTHER THREE SENSE SWITCHES IN THE DOWN POSITION.
4.1.5 DEPRESS THE "LOAD" PUSHBUTTON ON THE CONTROL PANEL.
4.1.6 VERIFY THAT THE SYSTEM LOADS. (THIS SHOULD TAKE ABOUT 45
SECONDS).
4.1.7 WHEN TERMINAL T0 DISPLAYS THE MAIN MENU, TYPE 1 AND <CR> TO
SELECT "NORMAL OPERATIONS".
4.1.8 THE DATE AND TIME WILL BE DISPLAYED. ENTER A <CR> FOR EACH IF
THEY ARE CORRECT OR ENTER THE CORRECT DATE AND TIME IF THEY
ARE NOT CORRECT.
4.1.9 VERIFY THAT THE SYSTEM INITIALIZES. (THIS TAKES ABOUT 30
SECONDS).
4.1.10 WHEN THE TERMINAL DISPLAYS "MAI-BASIC FOUR BOSS/VS TERMINAL
T0", DEPRESS THE ESCAPE KEY.
4.1.11 WHEN PROMPTED "ACCOUNT NAME:", ENTER YOUR ACCOUNT NAME.
4.1.12 WHEN PROMPTED "PASSWORD:", ENTER YOUR PASSWORD.
4.1.13 WHEN LOG-ON IS COMPLETE, TERMINAL T0 WILL DISPLAY "WELCOME TO
EAGLE'S NEST" AND "CR TO CONTINUE", DEPRESS THE <CR>.
4.1.14 THE TERMINAL T0 WILL DISPLAY THE "OS INFO" MATRIX AND "CR TO
CONTINUE". DEPRESS THE <CR>.
4.1.15 WHEN PROMPTED "!" AT T0, TYPE "DOWN.LOAD" AND <CR>.
4.1.16 WHEN PROMPTED "ENTER DEVICE NUMBER TO DOWNLOAD (0-63):", TYPE
THE NUMBER OF THE FIRST ISDC BOARD TO BE DOWNLOADED AND THEN
A <CR>.
4.1.17 THE TERMINAL WILL FIRST DISPLAY "DOWNLOAD IN PROGRESS" AND
THEN "DOWNLOAD COMPLETED" AND "CR TO CONTINUE". DEPRESS THE
<CR>.
4.1.18 REPEAT THE PREVIOUS 2 STEPS INSERTING THE NUMBER OF EACH ISDC
BOARD TO BE DOWNLOADED UNTIL ALL BOARD NUMBERS HAVE BEEN
ENTERED.
4.1.19 WHEN ALL ISDC BOARDS HAVE BEEN DOWNLOADED, DEPRESS CTL-IV.
4.1.20 WHEN PROMPTED "!", TYPE "RD.EAGLE" AND <CR>.
4.1.21 THE T0 TERMINAL WILL DISPLAY "SYSTEM 2000 REMOTE DIAGNOSTICS
REV XXXX" AND THE MAIN MENU.
4.1.22 IF IT IS NECESSARY TO CLEAR THE ERROR FILE, MOVE TO TERMINAL
T1 AND DEPRESS THE ESCAPE KEY.
4.1.23 WHEN PROMPTED "ACCOUNT NAME:", ENTER YOUR ACCOUNT NAME.
4.1.24 WHEN PROMPTED "PASSWORD:", ENTER YOUR PASSWORD.
4.1.25 WHEN LOG-ON IS COMPLETE, TERMINAL T1 WILL DISPLAY "WELCOME TO
EAGLE'S NEST" AND "CR TO CONTINUE", DEPRESS THE <CR>.
4.1.26 THE TERMINAL T1 WILL DISPLAY THE "OS INFO" MATRIX AND "CR TO
CONTINUE". DEPRESS THE <CR>.
4.1.27 WHEN PROMPTED "!", TYPE "DELETE .DIAG.*.RD.ERRST*" AND <CR>.
4.1.28 AS EACH FILE IS DISPLAYED, DEPRESS CTL-I TO DELETE THAT FILE
OR DEPRESS CTL-III TO KEEP THAT FILE.
4.1.29 WHEN ALL DESIRED ERROR FILES HAVE BEEN DELETED, TYPE RELEASE"
AND <CR>.
4.1.30 VERIFY THAT THE TERMINAL T1 LOGS-OFF.
4.1.31 AT THIS TIME, CONNECT A DOWNLOAD CABLE TO THE SCC1 PORT OF
EACH 2000 SYSTEM THAT IS TO BE TESTED.
4.2.1 VERIFY THAT A HOST DOWNLOAD CABLE IS CONNECTED TO THE SCC1 PORT
OF EACH 2000 SYSTEM TO BE TESTED AND THAT A PIT LOOPBACK
CONNECTOR IS CONNECTED TO EACH PARALLEL PRINTER PORT.
4.2.2 MOVE TO TERMINAL T0 OF THE HOST SYSTEM WHERE THE MAIN MENU IS
DISPLAYED AND TYPE "2" AND <CR> TO SELECT AND DISPLAY THE TEST
OPTIONS.
4.2.3 WHEN PROMPTED "ENTER ISDC PORT # (T2 TO TXX):", TYPE THE
NUMBERS OF THE PORTS DESIRED FOR THE SELECTING OF TESTS. THE
SAME TEST SELECTION MAY BE MADE FOR ONE PORT OR A GROUP OF
PORTS. e.g. 11-23 FOR A STRING OF PORTS OR 2,5,10 FOR A NUMBER
OF INDIVIDUAL PORTS. THEN TERMINMATE THE ENTRY WITH A <CR>.
4.2.4 WHEN THE TEST SELECTION MENU IS DISPLAYED, MODIFY THE
SELECTIONS TO MATCH THE SAMPLE MENU SHOWN IN FIGURE 1 BELOW FOR
ALL OPTIONS CONFIGURED IN THE SYSTEMS UNDER TEST. FOR
UNCONFIGURED ITEMS, SELECT 0 FOR 'RUNIN #MINS' AND 'RUN COUNT'
AND NONE FOR 'TESTS'.
FIGURE 1
-------- * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* SELECT/DISPLAY TEST OPTIONS FOR SYSTEMS UNDER TEST *
* *
* *
* *
* ENTER ISDC PORT # (T2 TO TXX, CTL-4 TO EXIT): X *
* *
* PROGRAM RUNIN RUN RESUME *
* NAME #MINS COUNT COUNT TESTS *
* *
* 1) MEMORY N/A 1 10 ALL *
* 2) NVRAM N/A 1 10 ALL *
* 3) MMU N/A 1 10 ALL *
* 4) CMB N/A 20 10 ALL *
* 5) PIT N/A 20 10 1-7 *
* 6) FWAY 0 0 0 NONE *
* 7) MCS 0 0 0 NONE *
* 8) LAN 0 0 0 NONE *
* 9) FLOPPY 0 0 0 NONE *
* 10) DISK 0 0 0 NONE *
* *
* ENTER NUMBER TO CHANGE (1-10, CTL-4=EXIT) *
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
4.2.5 TYPE "1" AND CR TO SELECT MEMORY TEST AND OBSERVE THE
DISPLAY AS SHOWN IN FIGURE 2 BELOW. FIGURE 2
--------
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* SELECT/DISPLAY TEST OPTIONS FOR SYSTEMS UNDER TEST *
* *
* ENTER ISDC PORT # (T2 TO TXX, CTL-4 TO EXIT): X *
* *
* DIAGNOSTIC PROGRAM NAME: FWAY *
* *
* 1) TESTS: NONE *
* 2) RUN COUNT: 0 *
* 3) RESUME COUNT: 0 *
* 4) NUMBER MINUTES TO 'RUNIN: N/A *
* *
* ENTER OPTION NUMBER TO CHANGE (1-4) *
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
4.2.6 TYPE "1" AND CR TO SELECT TESTS AND OBSERVE THE
DISPLAY AS SHOWN IN FIGURE 3 BELOW.
FIGURE 3 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
-------- * SELECT/DISPLAY TEST OPTIONS FOR SYSTEMS UNDER TEST *
* *
* ENTER ISDC PORT # (T2 TO TXX, CTL-4 TO EXIT): X *
* *
* LOGIC TEST OPTIONS FOR: X DIAGNOSTIC PROGRAM: MEMORY *
* 1)* NONEXISTANT MEMORY ACCESS *
* 2)* UPPER-BYTE PARITY *
* 3)* LOWER-BYTE PARITY *
* 4)* WRITE AND READ ZEROS AND ONES *
* 5)* UNIQUE MODULE ADDRESSING *
* 6) UNIQUE WORD ADDRESSING *
* 7) UNIQUE BYTE ADDRESSING *
* 8) MARCHING ONES AND ZEROS *
* 9) INTERCELL CROSSTALK *
* 10) WORST CASE DATA MOVEMENT *
* ENTER NUMBER (1-10, CTL-1=ALL, CTL-2=NONE, CTL-3=NEXT PAGE)*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
4.2.7 DEPRESS CTL-1 TO SELECT ALL TESTS AND VERIFY THAT AN ASTERISK
(*) APPEARS BETWEEN THE TEST NUMBER AND THE TEST TITLE
(e.g. 10)* WORST CASE DATA MOVEMENT) TO SHOW THAT THE TEST IS
SELECTED.
4.2.8 DEPRESS CTL-4 AND OBSERVE THAT THE DISPLAY RETURNS TO THE MENU
SHOWN IN FIGURE 2.
4.2.9 TYPE "2" AND <CR> FOR RUN COUNT.
4.2.10 WHEN PROMPTED "ENTER THE RUN COUNT (1-99999, CR=1):", DEPRESS
<CR> TO SELECT A RUN COUNT OF 1.
4.2.11 TYPE "3" AND <CR> FOR RESUME COUNT.
4.2.12 WHEN PROMPTED "ENTER THE RESUME COUNT (1-99999, CR=0):", TYPE
"10" AND <CR> TO SELECT A RESUME COUNT OF 10.
4.2.13 DEPRESS CTL-4 AND OBSERVE THAT THE DISPLAY RETURNS TO THE MENU
SHOWN IN FIGURE 1.
4.2.14 FROM THE MENU SHOWN IN FIGURE 1, SELECT THE NEXT TEST TO BE SET
UP BY REPEATING ALL STEPS FROM STEP 4.2.4.
4.2.15 WHEN ALL TEST OPTIONS HAVE BEEN SELECTED, REVERIFY ALL
SELECTIONS FROM THE MENU SHOWN IN FIGURE 1. 4.2.16 DEPRESS CTL-4 AND DISPLAY WILL PROMPT FOR MORE ISDC PORTS TO
SELECT/DISPLAY TEST OPTIONS. IF MORE PORTS ARE TO BE SETUP,
REPEAT THE ABOVE STEPS FROM STEP 4.2.2.
4.2.17 WHEN ALL DESIRED ISDC PORTS HAVE BEEN SETUP FOR TESTING,
DEPRESS CTL-4 TO RETURN TO THE MAIN MENU.
4.2.18 AT THE MAIN MENU, TYPE "3" AND <CR> TO SELECT TEST STATUSES.
4.2.19 THE DISPLAY WILL SHOW "DISPLAY TEST STATUSES" AND SHOW THE
NUMBER OF ISDC PORTS AND HSVDT'S. WHEN PROMPTED "ENTER ISDC
PORT #", DEPRESS <CR> TO SELECT ALL PORTS.
4.2.20 WHEN PROMPTED " ENTER HIGH SPEED TERMINAL (T0 TO T1, CTL-4 TO
EXIT):", TYPE "1" AND <CR>.
4.2.21 VERIFY THAT TERMINAL T1 DISPLAYS A CONTINUOUS SCROLLING TEST
STATUS FOR ALL PORTS.
4.2.22 AT TERMINAL T0, DEPRESS CTL-4 TO RETURN TO THE MAIN MENU.
4.2.23 AT THE MAIN MENU, TYPE "1" AND <CR>.
4.2.24 THE DISPLAY WILL BE "INITALIZE SYSTEMS TO TEST" AND THE NUMBER
OF HSVDT'S AND ISDC PORTS. WHEN PROMPTED "ENTER ISDC PORT #
(T2 TO TXX, CTL-4 TO EXIT):", TYPE THE NUMBERS OF THE PORTS
THAT ARE DESIRED TO BE TESTED. ONE PORT OR A GROUP OF PORTS.
e.g. 11-23 FOR A STRING OF PORTS OR 2,5,10 FOR A NUMBER OF
INDIVIDUAL PORTS MAY BE SELECTED AT ONE TIME.
4.2.25 WHEN PROMPTED "CR=START TX", DEPRESS <CR> FOR EACH PROMPT.
4.2.26 WHEN ALL DESIRED PORTS HAVE BEEN STARTED, DEPRESS CTL-4 TO
RETURN TO THE MAIN MENU.
4.2.27 PERFORM THE FOLLOWING STEPS AT EACH 2000 SYSTEM TO BE TESTED.
4.2.28 TURN ON THE 2000 SYSTEM POWER.
4.2.29 AT THE 2000 SYSTEM SCC0 TERMINAL, DEPRESS THE ESCAPE KEY
REPEATEDLY.
4.2.30 WHEN PROMPTED <DEBUG>, TYPE "BO SC1" AND <CR>.
4.2.31 WHEN PROMPTED <EXEC>, TYPE "OP RE" AND <CR>.
4.2.32 THE TESTING IS NOW UNDER THE CONTROL OF THE HOST. TO BE
CONSIDERED ACCEPTABLE (PASSED), ALL SELECTED TESTS MUST RUN
ERROR FREE UNTIL ABORTED BY THE TEST OPERATOR.
4.2.33 WHEN THE TEST IS COMPLETED, TYPE "6" AND <CR> AT T0. 4.2.34 THE DISPLAY WILL BE "ABORT TESTING OF SYSTEMS". WHEN PROMPTED
"ENTER ISDC PORT # (T2 TO TXX, CTL-4 TO EXIT):", TYPE THE
NUMBERS OF THE PORTS THAT ARE TO BE ABORTED AND TERMINATE EACH
ENTRY WITH A <CR>.
4.2.35 WHEN ALL DESIRED PORTS HAVE BEEN ABORTED, DEPRESS CTL-4 TO
RETURN TO THE MAIN MENU.
4.1A.1 CONNECT A VIDEO TERMINAL TO THE SYSTEM'S SCC0 PORT.
4.1A.2 INSTALL A BLANK TAPE INTO ANY TAPE DRIVES THAT ARE CONFIGURED.
4.1A.3 PLACE THE SYSTEM POWER SWITCH IN THE ON POSITION.
4.1A.4 WHEN THE SYSTEM PERFORMS THE SELF TEST PRESS THE CONTROL AND
"C" KEYS TOGETHER.
4.1A.5 VERIFY THAT THE SELF TEST CONTINUES AND INDICATES NO ERRORS.
4.1A.6 WHEN PROMPTED "BOOT DEVICE:", TYPE "wd" AND <CR>.
4.1A.7 WHEN PROMPTED "SYSTEM FILE:", TYPE "diag" AND <CR>.
4.1A.8 THE TERMINAL WILL DISPLAY "BOOTING FROM WD0".
4.1A.9 WHEN PROMPTED <EXEC>, TYPE "AUTO" AND <CR>.
4.1A.10 VERIFY THAT THE DIAGNOSTIC PROGRAM LOADS AND BEGINS TO RUN.
4.1A.11 VERIFY THAT THE TEST RUNS ERROR FREE FOR ONE COMPLETS PASS.
4.1A.12 WHEN THE AUTO TEST IS COMPLETE AND THE <EXEC> PROMPT IS
DISPLAYED, TYPE "LO SIT" AND <CR>.
4.1A.13 VERIFY THAT THE PROGRAM LOADS AND DISPLAYS A LIST OF THE
SUBSYSTEMS PRESENT.
4.1A.14 WHEN PROMPTED <SIT>, TYPE "RUN" AND <CR>.
4.1A.15 THE TEST WILL BEGIN TO RUN. VERIFY THAT EVERY 15 TO 20 SECONDS
A "NEWS UPDATE" WILL BE DISPLAYED SHOWING THE ELAPSED TEST
TIME AND THE STATUS OF EACH RUNNING TASK.
4.1A.16 VERIFY THAT ALL TASKS ARE RUNNING (ESPECIALLY MC00). IF NOT
PRESS THE ESCAPE KEY AND TYPE "START MC00" (OR WHATEVER TASK
NAME IS REQUIRED) AND <CR>. THEN TYPE "RUN" AND <CR> TO
DISPLAY THE NEWS UPDATE.
4.1A.17 VERIFY THAT THE TEST RUNS ERROR FREE FOR THE REQUIRED LENGTH
OF TIME. ACCUMULATED ERRORS ARE DISPLAYED IN THE TWO RIGHT
HAND COLUMNS OF THE NEWS UPDATE.
4.1A.18 WHEN THE TEST HAS COMPLETED, PRESS THE ESCAPE KEY.
4.1A.19 WHEN PROMPTED <SIT>, POWER DOWN THE SYSTEM.
* CAUTION: DO NOT DISCONNECT POWER OR RESET SYSTEM WHEN OPERATING FROM
A HARD DISK.
* ALL ENTRIES MUST BE IN LOWER CASE LETTERS WHEN OPERATING FROM A HARD
DISK UNLESS OTHERWISE INDICATED.
4.3.1 TURN ON THE POWER TO THE SYSTEM.
4.3.2 VERIFY THAT THE SYSTEM BOOTS FROM WD0.
4.3.3 WHEN PROMPTED "UPDATE CLOCK",ENTER THE CORRECT TIME AND DATE
IN THE FOLLOWING FORMAT: 194500am 083085.
4.3.4 WHEN PROMPTED <ADMIN>, DEPRESS THE CONTROL AND D KEYS TOGETHER.
4.3.5 WHEN PROMPTED "SINGLE, MULTI OR SHUTDOWN", TYPE "multi" AND
<CR>.
4.3.6 VERIFY THAT THE SYSTEM ADVANCES TO MULTI USER MODE AND DISPLAYS
THE MAI2000 LOGO.
4.3.7 WHEN PROMPTED "ACCOUNT NAME", TYPE "admin" AND <CR>.
4.3.8 WHEN PROMPTED <ADMIN>, TYPE "miniq" AND <CR>.
4.3.9 AT THE MINIQ MENU, TYPE "4" AND <CR> TO SELECT CONTINUOUS
RUNNING.
4.3.10 MONITOR THE TERMINAL PERIODICLY TO VERIFY THAT THE SYSTEM IS
STILL RUNNING. (A FAILURE IS INDICATED BY THE DISPLAY REMAINING
STATIC.
4.3.11 WHEN THE TEST HAS RUN FOR THE DESIRED LENGTH OF TIME, (ELAPSED
TIME IS DISPLAYED ON THE TERMINAl) PRESS THE ESCAPE KEY TO STOP
THE TEST. THE START TIME AND THE STOP TIME OF THE TEST WILL
THEN BE DISPLAYED ON THE TERMINAL. RECORD THE TIME AND PRESS
THE <CR> TO CONTINUE.
4.3.12 THE SYSTEM WILL NOW CHECK FOR LOST FILES. IF NONE HAVE BEEN
LOST THE DISPLAY WILL BE "NO FILES FOUND". HOWEVER, IF THE
INDICATION IS THAT FILES HAVE BEEN LOST THEN THE DISK MUST BE
RECOPIED WITH A NEW OS AND THEN RETESTED.
4.3.13 IF NO FILES HAVE BEEN LOST, PRESS THE <CR> TO CONTINUE.
4.3.14 THE SYSTEM WILL NOW DISPLAY THE ERROR LOG. VERIFY THAT NO
ERRORS HAVE OCCURRED. IF ANY ERRORS ARE FOUND, THE SYSTEM MUST
BE REJECTED.
4.3.15 AT THE TERMINAL, TYPE "shutdown 0" AND <CR>.
4.3.16 VERIFY THAT THE SYSTEM DISPLAYS SHUTTING DOWN IN 15 SECONDS AND
ADVANCES TO SINGLE USER MODE.
4.3.17 WHEN PROMPTED <ADMIN>, TYPE "delete miniq" AND <CR>.
4.3.18 WHEN PROMPTED <ADMIN>, DEPRESS THE CONTROL AND D KEYS TOGETHER.
4.3.19 WHEN PROMPTED "SINGLE, MULTI OR SHUTDOWN", TYPE "shutdown" AND
<CR>.
4.3.20 WHEN "PRESS 'RETURN' TO REBOOT" IS DISPLAYED, TURN OFF THE
SYSTEM POWER
* CAUTION: DO NOT DISCONNECT POWER OR RESET SYSTEM WHEN OPERATING FROM
A HARD DISK.
* ALL ENTRIES MUST BE IN LOWER CASE LETTERS WHEN OPERATING FROM A HARD
DISK UNLESS OTHERWISE INDICATED.
4.4.1 SERIAL & PARALLEL PORTS FINAL TEST
4.4.1.1 CONNECT A LINE PRINTER TO THE CMB'S PARALLEL PORT.
4.4.1.2 TURN ON THE POWER TO THE SYSTEM.
4.4.1.3 VERIFY THAT THE SYSTEM BOOTS FROM WD0.
4.4.1.4 WHEN PROMPTED "UPDATE CLOCK", IF THE DATE AND TIME ARE
CORRECT, PRESS <CR>. IF NOT, UPDATE AS NECESSARY.
4.4.1.5 WHEN PROMPTED <ADMIN>, DEPRESS THE CONTROL AND D KEYS
TOGETHER.
4.4.1.6 WHEN PROMPTED "SINGLE, MULTI OR SHUTDOWN", TYPE
"multi" AND <CR>.
4.4.1.7 VERIFY THAT THE SYSTEM ADVANCES TO MULTI USER MODE AND
DISPLAYS THE MAI/2000 LOGO.
4.4.1.8 PRESS THE ESCAPE KEY.
4.4.1.9 WHEN PROMPTED "ACCOUNT NAME", TYPE "admin" AND <CR>.
4.4.1.10 WHEN PROMPTED <ADMIN>, TYPE "test1" AND <CR>.
4.4.1.11 VERIFY THAT THE CONSOLE TERMINAL DISPLAYS AN
ALPHANUMERIC RIPPLE PATTERN THAT FILLS THE SCREEN.
4.4.1.12 WHEN PROMPTED <ADMIN>, PRESS THE CONTROL AND D KEYS
TOGETHER.
4.4.1.13 VERIFY THAT THE TERMINAL DISPLAYS THE MAI LOGO.
4.4.1.14 REPEAT THE SIX PREVIOUS STEPS FOR EACH AND EVERY
SERIAL PORT ON THE SYSTEM UNDER TEST.
4.4.1.15 RETURN TO THE CONSOLE TERMINAL,T0, AND PRESS THE
ESCAPE KEY.
4.4.1.16 WHEN PROMPTED "ACCOUNT NAME", TYPE "admin" AND <CR>.
4.4.1.17 WHEN PROMPTED <ADMIN>, TYPE "test2" AND <CR>.
4.4.1.18 VERIFY THAT THE LINE PRINTER PRINTS A 3/4 PAGE, 132
COLUMN ALPHANUMERIC RIPPLE PATTERN.
4.4.1.19 WHEN THE TEST RESULTS HAVE BEEN VERIFIED AND ARE
CORRECT, CONTINUE ON TO THE NEXT SECTION.
NOTE: PERFORM EACH OF THE FOLLOWING SECTIONS THAT APPLY TO THE CONFIGURATION
OF THE SYSTEM UNDER TEST.
4.4.2 MCS TAPE DRIVES
4.4.2.1 CONTINUING FROM ONE OF THE PREVIOUS PARAGRAPHS, THE
SYSTEM SHOULD BE BOOTED AND IN 'MULTI USER' MODE.
4.4.2.2 INSTALL A BLANK TAPE INTO THE MCS TAPE DRIVE.
4.4.2.3 WHEN PROMPTED <ADMIN>, TYPE "test3" AND <CR>.
4.4.2.4 VERIFY THAT THE TAPE STARTS TO RUN AND THAT IN ABOUT
30 SECONDS THE TAPE LABEL IS DISPLAYED.
4.4.2.5 VERIFY THAT IN ABOUT ANOTHER 60 SECONDS THAT THE
TERMINAL DISPLAYS "COMPILING SAVE SET AND REWINDING
TAPE" AND THEN INDICATES THE NUMBER OF FILES SAVED.
4.4.2.6 THE TERMINAL WILL INDICATE THE NAMES OF THE FILES
BEING COMPARED AND A SUMMARY OF THE RESULTS. VERIFY
ALL THE FILES HAVE BEEN COMPARED AND THAT THERE ARE
NO MISCOMPARES INDICATED.
4.4.2.7 WHEN THE TEST RESULTS HAVE BEEN VERIFIED AND ARE
CORRECT, CONTINUE ON TO THE NEXT SECTION.
4.4.3 MTS TAPE DRIVES
4.4.3.1 CONTINUING FROM ONE OF THE PREVIOUS PARAGRAPHS, THE
SYSTEM SHOULD BE BOOTED AND IN 'MULTI USER' MODE.
4.4.3.2 INSTALL A BLANK TAPE INTO THE MTS TAPE DRIVE.
4.4.3.3 WHEN PROMPTED <ADMIN>, TYPE "test4" AND <CR>.
4.4.3.4 VERIFY THAT THE TAPE STARTS TO RUN AND THAT IN ABOUT
30 SECONDS THE TAPE LABEL IS DISPLAYED.
4.4.3.5 VERIFY THAT IN ABOUT ANOTHER 60 SECONDS THAT THE
TERMINAL DISPLAYS "COMPILING SAVE SET AND REWINDING
TAPE" AND THEN INDICATES THE NUMBER OF FILES SAVED.
4.4.3.6 THE TERMINAL WILL INDICATE THE NAMES OF THE FILES
BEING COMPARED AND A SUMMARY OF THE RESULTS. VERIFY
ALL THE FILES HAVE BEEN COMPARED AND THAT THERE ARE
NO MISCOMPARES INDICATED.
4.4.3.7 WHEN THE TEST RESULTS HAVE BEEN VERIFIED AND ARE
CORRECT, CONTINUE ON TO THE NEXT SECTION.
4.4.4 LAN CONTROLLER
4.4.4.1 CONTINUING FROM ONE OF THE PREVIOUS PARAGRAPHS, THE
SYSTEM SHOULD BE BOOTED AND IN 'MULTI USER' MODE.
4.4.4.2 CONNECT THE LAN TEST CABLE TO THE LAN PCBA OF THE
SYSTEM UNDER TEST.
4.4.4.3 WHEN PROMPTED <ADMIN>, TYPE "test5" AND <CR>.
4.4.4.4 VERIFY THAT THE MAIN MENU OF THE 'BITS TEST PROCEDURES
VIEWING SYSTEM' IS DISPLAYED.
4.4.4.5 SELECT ANY DOCUMENT FROM THE MENUS DISPLAYED AND
VERIFY THAT THE SELECTED DOCUMENT IS DISPLAYED ON THE
TERMINAL.
4.4.4.6 THE TEST IS SATISIFIED IF THE SELECTED DOCUMENT CAN BE
DISPLAYED SINCE ALL OF THESE DOCUMENTS RESIDE ON
ANOTHER SYSTEM IN THE LAN NETWORK.
4.4.4.7 WHEN THE TEST RESULTS HAVE BEEN VERIFIED AND ARE
CORRECT, PRESS THE ESCAPE KEY TO EXIT THE TEST AND
THEN CONTINUE ON TO THE NEXT SECTION.
4.4.5 WD1 - SECOND HARD DISK DRIVE
4.4.5.1 CONTINUING FROM ONE OF THE PREVIOUS PARAGRAPHS, THE
SYSTEM SHOULD BE BOOTED AND IN 'MULTI USER' MODE.
4.4.5.2 WHEN PROMPTED <ADMIN>, TYPE "test6" AND <CR>.
4.4.5.3 WHEN THE "ADD-ON DRIVE SELECTION" MENU IS DISPLAYED,
ENTER "1" TO SELECT WD1 (SECOND DISK DRIVE). THE
OTHER TWO SELECTIONS ARE FOR PHOENIX SYSTEMS ONLY.
4.4.5.4 THE TEST WILL BEGIN. WHEN THE READ/WRITE PORTION HAS
BEEN COMPLETED, AND THE TERMINAL PROMPTS "WHEN READY
TO CONTINUE, PRESS <CR>", PRESS THE <CR>.
4.4.5.5 VERIFY THAT AN ALPHA-NUMERIC RIPPLE PATTERN IS
DISPLAYED ON THE TERMINAL.
4.4.5.6 WHEN THE PATTERN HAS BEEN VERIFIED, PRESS <CR> TO
CONTINUE.
4.4.5.7 VERIFY THAT THE TERMINAL DISPLAYS THAT THE TEST FILES
( /mntwd1/test/XX ) ARE BEING DELETED.
4.4.5.8 WHEN PROMPTED "ADMIN>", THE TEST IS COMPLETE.
4.5.1 IF CONTINUING ON FROM THE PREVIOUS SECTION, THE SYSTEM SHOULD
BE BOOTED UP AND THE <ADMIN> PROMPT WILL BE DISPLAYED, IF NOT,
BOOT THE SYSTEM UP AND AT THE <ADMIN> PROMPT, TYPE "cleandisk"
AND <CR>.
4.5.2 A WARNING WILL BE DISPLAYED ON THE TERMINAL THAT WILL PROVIDE
AN OPTION TO ABORT THE DELETION OR TO CONTINUE WITH THE
DELETION. NOTE: IF THESE PROGRAMS ARE DELETED IT WILL REQUIRE
THAT THEY BE RELOADED ON TO THE DISK IF THE LABEL OR MINIQ
PROGRAMS OR ANY OTHER TEST PROGRAM NEEDS TO BE RERUN.
4.5.3 IF THE DELETION IS CONTINUED, VERIFY THAT THE TERMINAL SHOWS
THE LIST OF THE DIRECTORIES AND FILES BEING DELETED.
4.5.4 WHEN THE DELETIONS ARE COMPLETE AND THE <ADMIN> PROMPT IS
DISPLAYED, TYPE "shutdown 0" AND <CR>.
4.5.5 VERIFY THAT THE SYSTEM DISPLAYS SHUTTING DOWN IN 15 SECONDS
AND ADVANCES TO SINGLE USER MODE.
4.5.6 WHEN PROMPTED <ADMIN>, DEPRESS THE CONTROL AND D KEYS TOGETHER.
4.5.7 WHEN PROMPTED "SINGLE, MULTI OR SHUTDOWN", TYPE "shutdown" AND
<CR>.
4.5.8 WHEN "PRESS 'RETURN' TO REBOOT" IS DISPLAYED, TURN OFF THE
SYSTEM POWER.
** IF THE SYSTEM UNDER TEST HAS A SPECIFIC CUSTOMER'S SSN AND
CONFIGURATION RECORD INSTALLED (AN MSO UNIT), OMIT THIS PARAGRAPH. ** A SYSTEM OR DISK DRIVE MUST NEVER BE SHIPPED WITH THE TEST
CONFIGURATION RECORD INSTALLED. THIS CONFIGURATION RECORD MUST
BE REMOVED PRIOR TO SHIPMENT. 4.6.1 WITH THE WINCHESTER DISK DRIVE INSTALLED IN THE SYSTEM AND A
DIAGNOSTIC DISKETTE INSERTED INTO THE FLOPPY DRIVE, TURN ON THE
SYSTEM POWER AND BOOT FROM FD0.
4.6.2 WHEN <EXEC> IS DISPLAYED, TYPE "LO DUTIL" AND <CR>.
4.6.3 WHEN THE <DUTIL> PROMPT IS DISPLAYED, TYPE "writeok" AND <CR>.
4.6.4 WHEN THE <DUTIL> PROMPT IS DISPLAYED AGAIN, TYPE "config" AND
<CR>.
4.6.5 WHEN THE CONFIG RECORD UTILITY MENU IS DISPLAYED, TYPE "3" AND
<CR> TO DESTROY THE CONFIGURATION RECORD.
4.6.6 WHEN THE UNIT SELECTION MENU IS DISPLAYED, TYPE "1" AND <CR>
TO SELECT DRIVE 0.
4.6.7 WHEN THE CONFIG RECORD UTILITY MENU IS DISPLAYED AGAIN, THE
PROCEDURE IS COMPLETE.
4.6.8 TURN OFF THE SYSTEM POWER.
** IF THE SYSTEM UNDER TEST HAS A SPECIFIC CUSTOMER'S SSN AND
CONFIGURATION RECORD INSTALLED (AN MSO UNIT), OMIT THIS PARAGRAPH. 4.7.1 REMOVE THE SOCKETED INTEGRATED CIRCUIT AT LOCATION 8Z ON THE
CMB AND REPLACE IT WITH THE "SSN TEST IC".
4.7.2 INSTALL AN "SSN" TAPE INTO THE STREAMER TAPE DRIVE.
4.7.3 TURN ON THE SYSTEM POWER AND PRESS THE CONTROL AND "C" KEYS
TOGETHER TO SELECT ALTERNATE-LOAD.
4.7.4 WHEN PROMPTED "BOOT DEVICE:", TYPE "cs" AND <CR>.
4.7.5 WHEN PROMPTED "SYSTEM FILE:", TYPE "ssn" AND <CR>. 4.7.6 THE TERMINAL WILL DISPLAY "BOOTING FROM CS0......." AND THEN
"BOOT COMPLETE" AND THE EXISTING SYSTEM SERIAL NUMBER.
4.7.7 WHEN PROMPTED "NEW SERIAL NUMBER: 2", TYPE IN THE NEW SSN IN
THE FORM "000-9XXXX FOLLOWED BY A <CR>.
4.7.8 WHEN THE INSTALLATION IS COMPLETE, POWER DOWN THE SYSTEM.
4.7.9 WHEN THE SYSTEM POWER IS OFF, REPLACE THE ORIGINAL IC AT
LOCATION 8Z ON THE CMB. * * DO NOT SHIP THE SECURITY IC * *
4.6.10 TURN ON THE SYSTEM AND OBSERVE THE SELF-TEST TO VERIFY THAT THE
SYSTEM SERIAL NUMBER DISPLAYED IS CORRECT.
THIS PROCEDURE REQUIRES A SEPARATE TEST STATION. THIS STATION WILL CONSIST
OF SERIES 2000 SYSTEM WITH A DISK CONTROLLER, A STREAMER TAPE DRIVE, AN
MTCS CONTROLLER AND A MINIMUM OF 768K OF MEMORY.
THE TYPE OF DRIVE (WDD OR FLOPPY), AND WHERE THE DRIVE IS TO BE USED WILL
DICTATE WHICH TESTS IN THIS SECTION ARE TO BE USED. REFER TO THE TABLE
BELOW TO SELECT THE APPROPRIATE TEST SECTIONS.
CHECK LIST
----------
| DISK TYPE | TESTS | SECT | REQUIREMENT |
|===============================================================|
| ALL WDDS | FORMAT | 5.1.1| FOR ALL HARD DISKS |
| | VERIFICATION | 5.1.2| |
|---------------------------------------------------------------|
| MASTER WDD | TAPE LOAD OS | 5.3 | FOR NEW OS RELEASES ONLY |
|---------------------------------------------------------------|
| WDD 0 | DISK TO DISK | 5.2 | FOR 1st HARD DISK SHIPPED|
| (FIRST DISK | OS LOAD | | AS A KIT, RUN MINIQ 1 HR.|
| DRIVE) | | | MINIMUM IN A SYSTEM. |
| | | | IF INSTALLED IN A BASE |
| | | | SYSTEM, TEST PER SYSTEM |
| | | | REQUIREMENTS. |
|---------------------------------------------------------------|
| WDD 1 | RUNIN | 5.4 | FOR 2ND HARD DISKS TO BE |
| (SECOND DISK | | | SHIPPED AS A KIT |
| DRIVE) | | | RUN 5 MINUTES, MINIMUM |
|---------------------------------------------------------------|
| ALL FLOPPIES | RUNIN | 5.5 | FOR ALL FLOPPY DRIVES |
| | | | RUN 5 MINUTES, MINIMUM |
---------------------------------------------------------------
* NOTE SET THE JUMPERS ON THE DISK CONTROLLER FOR EACH TYPE OF DISK
DRIVE AS SHOWN IN SECTION 2 OF THIS PROCEDURE.
5.1.1 FORMATTING
5.1.1.1 CONFIGURE THE SYSTEM TO BOOT FROM FD0.
5.1.1.2 SET THE NEW DISK TO DRIVE #0 (SEE SECTION 2).
5.1.1.3 INSTALL THE DISK TO BE FORMATTED.
5.1.1.4 TURN ON THE SYSTEM POWER.
5.1.1.5 INSTALL A #1 DIAGNOSTIC DISKETTE INTO THE FLOPPY DISK
DRIVE.
5.1.1.6 THE TERMINAL WILL DISPLAY THE SYSTEM SELF-TEST AND THE
FLOPPY DRIVE WILL BEGIN TO READ AND THE TERMINAL WILL
DISPLAY "BOOTING FROM FD0......." AND "BOOT COMPLETE".
5.1.1.7 WHEN <EXEC> IS DISPLAYED, TYPE "LO DUTIL" AND <CR>.
5.1.1.8 WHEN THE <DUTIL> PROMPT IS DISPLAYED, TYPE "DUTIL"
AND <CR>.
5.1.1.9 WHEN THE DISK UTILITIES MENU IS DISPLAYED, ENTER "1"
AND <CR> TO SELECT DISK FORMATTER.
5.1.1.10 WHEN THE DISK FORMATTER MENU IS DISPLAYED, ENTER "4"
AND <CR> TO SELECT FORMAT AND DEFECT MAPPING.
5.1.1.11 WHEN THE DRIVE TYPE MENU IS DISPLAYED, ENTER THE
APPROPRAITE NUMBER FOR THE DRIVE TYPE BEING USED AND
<CR>.
5.1.1.12 WHEN THE UNIT SELECTION MENU IS DISPLAYED, ENTER "1"
AND <CR> TO SELECT DRIVE 0, THE PRIMARY UNIT.
5.1.1.13 THE DEFECT INFORMATION WILL NOW BE REQUESTED. THIS
INFORMATION CAN EITHER BE FOUND MARKED ON THE BODY OF
THE DISK ITSELF OR ON A PRINTED LIST ACCOMPANYING THE
DISK. IF THERE ARE DEFECTS, ENTER THE INFORMATION AS
REQUESTED BY EACH PROMPT. TERMINATE EACH ENTRY WITH A
<CR>. WHEN THERE ARE NO MORE DEFECTS TO ENTER, OR
THERE ARE NO DEFECTS, ENTER A <CR>.
5.1.1.14 WHEN ASKED "DO YOU WANT TO EDIT DEFECT LIST ?",
ENTER "N" AND <CR>.
5.1.1.15 WHEN ASKED TO CONTINUE OR ABORT, ENTER CR TO CONTINUE.
5.1.1.16 THE DISK WILL REFOFMAT AND THE DISPLAY WILL SHOW
<<START REFORMATTING PROCEDURE>>.
5.1.1.17 WHEN COMPLETE THE DISPLAY WILL SHOW <<DISK FORMAT
COMPLETE>> AND <<SAVING DEFECT MAP ON DISK>>
5.1.1.18 DEPRESS THE ESCAPE KEY TO EXIT DUTIL.
5.1.2 FAULT MAP VERIFICATION
5.1.2.1 CONFIGURE THE SYSTEM TO BOOT FROM FD0.
5.1.2.2 INSTALL THE DISK TO BE VERIFIED.
5.1.2.3 TURN ON THE SYSTEM POWER.
5.1.2.4 INSTALL A #1 DIAGNOSTIC DISKETTE INTO THE FLOPPY DISK
DRIVE.
5.1.2.5 THE TERMINAL WILL DISPLAY THE SYSTEM SELF-TEST AND THE
FLOPPY DRIVE WILL BEGIN TO READ AND THE TERMINAL WILL
DISPLAY "BOOTING FROM FD0......." AND "BOOT COMPLETE".
5.1.2.6 WHEN <EXEC> IS DISPLAYED, TYPE "LO DUTIL" AND <CR>.
5.1.2.7 WHEN THE <DUTIL> PROMPT IS DISPLAYED, TYPE "DUTIL"
AND <CR>.
5.1.2.8 WHEN THE DISK UTILITIES MENU IS DISPLAYED, ENTER "2"
AND <CR> TO SELECT READ ONLY UTILITIES.
5.1.2.9 WHEN THE DISK FORMATTER MENU IS DISPLAYED, ENTER "4"
AND <CR> TO SELECT THE DEFECT MAP DISPLAY. 5.1.2.10 WHEN THE DRIVE TYPE MENU IS DISPLAYED, ENTER THE
APPROPRAITE NUMBER FOR THE DRIVE TYPE BEING USED
AND <CR>.
5.1.2.11 WHEN THE UNIT SELECTION MENU IS DISPLAYED, ENTER THE
APPROPRAITE NUMBER TO SELECT EITHER DRIVE 0 OR 1.
5.1.2.12 THE DEFECT MAP WILL NOW BE DISPLAYED. VERIFY THAT
THE NUMBER OF DEFECTS AND THE DEFECTS DISPLAYED
CORRELATE WITH THE INFORMATION FOUND MARKED ON THE
BODY OF THE DRIVE ITSELF OR ON A PRINTED LIST
ACCOMPANYING THE DRIVE. FOR MICROPOLIS AND MAXTOR
DRIVES, ALL CORRELATION SHOULD BE DIRECT. FOR RODIME
DRIVES, HEAD AND CYLINDER CORRELATION IS DIRECT BUT
THE SECTORS ARE NOT. REFER TO TABLE 5.1 (FOLLOWING
STEP 5.1.2.13 FOR SECTOR CORRELATION. ANY DRIVE THAT
DOES NOT CORRELATE MUST BE REFORMATTED AND REVERIFIED.
5.1.2.13 WHEN COMPLETE, DEPRESS THE ESCAPE KEY TO EXIT DUTIL
AND TURN OFF THE SYSTEM POWER.
TABLE 5.1 RODIME FAULT MAP CONVERSION TABLE
REF ENTER RODIME
5.1.2.12 SECTOR # VERIFY FAULTS ON FORMATTED DISK
-------- -------------------------------
SECTORS SECTORS BFIND (DEC.) 0 0 150
1 0 & 1 150 & 728
2 1 728
3 1 & 2 728 & 1306
4 2 1306
5 2 & 3 1306 & 1884
6 3 1884
7 3 & 4 1884 & 2462
8 4 2462
9 4 & 5 2462 & 3040
10 5 3040
11 5 & 6 3040 & 3618
12 6 3618
13 6 & 7 3618 & 4196
14 7 & 8 4196 & 4774
15 8 4774
16 8 & 9 4774 & 5352
17 9 5352
18 9 & 10 5352 & 5930
19 10 5930
20 10 & 11 5930 & 6508
21 11 6508
22 11 & 12 6508 & 7086
23 12 7086
24 12 & 13 7086 & 7664
25 13 7664
26 13 & 14 7664 & 8242
27 14 8242
28 14 & 15 8242 & 8820
29 15 & 16 8820 & 9398
30 16 9398
31 16 9398
32 16 9398
COPYING THE OS FROM DISK TO DISK CAN ONLY BE PERFORMED ON SIMILAR DISK
TYPES AND SIZES. A SEPARATE MASTER DISK IS REQUIRED FOR EACH TYPE AND
SIZE OF DISK AVAILABLE.
5.2.1 CONFIGURE THE SYSTEM TO BOOT FROM FD0.
5.2.2 SET THE NEW DISK TO DRIVE #0 (SEE SECTION 2).
5.2.3 SET THE MASTER DISK TO DRIVE #1 (SEE SECTION 2).
5.2.4 CONNECT A RADIAL CABLE FROM EACH DRIVE TO THE WDD CONTROLLER
(DRIVE #0 TO J4 & DRIVE #1 TO J5).
5.2.5 CONNECT THE DASIE CHAIN CABLE'S END CONNECTORS TO EACH DRIVE
AND THE CENTER CONNECTOR TO THE CONTROLLER.
5.2.6 TURN ON THE SYSTEM POWER.
5.2.7 INSTALL A #1 DIAGNOSTIC DISKETTE INTO THE FLOPPY DISK DRIVE.
5.2.8 THE TERMINAL WILL DISPLAY THE SYSTEM SELF-TEST AND THE FLOPPY
DRIVE WILL BEGIN TO READ AND THE TERMINAL WILL DISPLAY "BOOTING
FROM FD0............" AND "BOOT COMPLETE".
5.2.9 WHEN <EXEC> IS DISPLAYED, TYPE "LO DUTIL" AND <CR>.
5.2.10 WHEN THE <DUTIL> PROMPT IS DISPLAYED, TYPE "DUTIL" AND <CR>.
5.2.11 WHEN THE DISK UTILITIES MENU IS DISPLAYED, ENTER "3" AND <CR>
TO SELECT COPY DISK.
5.2.12 WHEN PROMPTED "THIS WILL COPY AN ENTIRE DISK, AND DESTROY THE
TARGET DISK DATA. CONTINUE (Y OR N)? >>", TYPE "Y" AND <CR>.
5.2.13 *CAUTION- AN IMPROPPER ENTRY AT THIS STEP COULD DESTROY THE
DATA ON A MASTER DISK.* WHEN THE COPY DISK MENU IS DISPLAYED,
ENTER "2" AND <CR> TO SELECT COPYING FROM DRIVE 1 TO DRIVE 0.
5.2.14 THE COPYING WILL BEGIN AND A SERIES OF DOTS WILL BE DISPLAYED
TO INDICATE THE PROGRESS.
5.2.15 WHEN THE COPYING IS COMPLETE, DEPRESS THE ESCAPE KEY.
5.2.16 WHEN THE <DUTIL> PROMPT IS DISPLAYED AGAIN, TYPE "writeok" AND
<CR>.
5.2.17 WHEN THE <DUTIL> PROMPT IS DISPLAYED AGAIN, TYPE "config" AND
<CR>.
5.2.18 WHEN THE CONFIG RECORD UTILITY MENU IS DISPLAYED, TYPE "2" AND
<CR> TO COPY THE CONFIGURATION RECORD FROM DRIVE 1 TO 0.
5.2.19 WHEN PROMPTED TO VERIFY COPYING FROM DRIVE 1 TO 0, VERIFY
AND THEN TYPE "y" AND <CR>.
5.2.20 WHEN THE CONFIG RECORD UTILITY MENU IS DISPLAYED AGAIN, THE
PROCEDURE IS COMPLETE. TURN OFF THE POWER AND MARK THE DRIVE.
THIS PROCEDURE IS ONLY USED TO COPY NEW OS RELEASES FROM TAPE TO HARD
DISK. THE COPIED DISKS WILL BE USED AS MASTERS FOR COPYING TO OTHER
DISKS. A SEPARATE MASTER DISK IS REQUIRED FOR EACH TYPE AND SIZE OF
DISK AVAILABLE. ALL TERMINAL ENTRIES MUST BE IN LOWER CASE LETTERS.
5.3.1 INSTALL DIAGNOSTICS
NOTE: THIS PARAGRAPH IS REQUIRED WHEN USING A DRIVE THAT HAS ONLY BEEN
FORMATTED AND HAS NOT HAD DIAGNOSTICS INSTALLED. USE PARAGRAPH 5.3.1A
WHEN UPDATING A DIAGNOSTICS RELEASE ONTO AN EXISTING MASTER DISK DRIVE.NOTE: WHEN INSTALLING A NEW DIAGNOSTIC RELEASE, THE OS WILL HAVE TO BE
REINSTALLED ALSO. 5.3.1.1 SELECT A TESTED AND FORMATTED DISK DRIVE TO BE USED AS
A MASTER OS DISK.
5.3.1.2 SET NEW DISK TO DRIVE #0 (SEE SECTION 2).
5.3.1.3 INSTALL THE NEW DISK INTO THE SYSTEM.
5.3.1.4 INSTALL A DIAGNOSTIC TAPE OF THE LATEST REVISION INTO
THE TAPE DRIVE.
5.3.1.5 TURN ON THE SYSTEM POWER.
5.3.1.6 WHEN THE SELF TEST IS DISPLAYED, DEPRESS THE CONTROL
AND C KEYS TOGETHER.
5.3.1.7 WHEN PROMPTED "BOOT DEVICE:", TYPE "CS" AND <CR>.
5.3.1.8 WHEN PROMPTED "SYSTEM FILE:", PRESS <CR>.
5.3.1.9 THE TAPE DRIVE WILL BEGIN TO READ AND THE TERMINAL
WILL DISPLAY "BOOTING FROM CS0........." AND "BOOT
COMPLETE". WHEN THE PROPRIETARY NOTICE IS DISPLAYED,
PRESS THE <CR> TO CONTINUE.
5.3.1.10 WHEN <EXEC> IS DISPLAYED, TYPE "SERVICE" AND <CR>.
5.3.1.11 WHEN PROMPTED "PASSWD>", TYPE "B4BUS" AND <CR>.
5.3.1.12 WHEN <EXEC> IS DISPLAYED, TYPE "SBINIT" AND <CR>.
5.3.1.13 WHEN ASKED IF DISK DRIVE WAS FORMATTED BY 'DUTIL',
ENTER "Y".
5.3.1.14 WHEN PROMPTED "SECTORS?", TYPE "1200" AND <CR>.
5.3.1.15 WHEN PROMPTED "DESTROY:",ENTER "Y".
5.3.1.16 WHEN PROMPTED "DISK NAME", PRESS <CR>.
5.3.1.17 WHEN <EXEC> IS DISPLAYED, TYPE "INSTALL" AND <CR>.
5.3.1.18 WHEN ASKED "DESTROY INSTALL?", TYPE "N".
5.3.1.19 VERIFY THAT THE INSTALLATION STARTS. EACH TIME THE
SYSTEM PROMPTS "DELETE OLD COPY?", ENTER "Y".
5.3.1.20 WHEN THE INSTALLATION IS COMPLETE AND <EXEC> IS
DISPLAYED, CONTINUE ON TO THE NEXT PARAGRAPH.
NOTE: THIS PARAGRAPH IS REQUIRED WHEN UPDATING A DIAGNOSTICS RELEASE ONTO AN
EXISTING MASTER DISK DRIVE. USE PARAGRAPH 5.3.1 WHEN USING A DRIVE THAT
HAS ONLY BEEN FORMATTED AND HAS NOT HAD DIAGNOSTICS INSTALLED BEFORE.NOTE: WHEN INSTALLING A NEW DIAGNOSTIC RELEASE, THE OS WILL HAVE TO BE
REINSTALLED ALSO. 5.3.1A.1 ADDRESS THE MASTER DISK AS WD0.
5.3.1A.2 INSTALL THE MASTER DISK INTO THE SYSTEM.
5.3.1A.3 INSTALL A DIAGNOSTIC TAPE OF THE LATEST REVISION INTO
THE TAPE DRIVE.
5.3.1A.4 TURN ON THE SYSTEM POWER.
5.3.1A.5 WHEN THE SELF TEST IS DISPLAYED, DEPRESS THE CONTROL
AND C KEYS TOGETHER.
5.3.1A.6 WHEN PROMPTED "BOOT DEVICE:", TYPE "CS" AND <CR>.
5.3.1A.7 WHEN PROMPTED "SYSTEM FILE:", PRESS <CR>.
5.3.1A.8 THE TAPE DRIVE WILL BEGIN TO READ AND THE TERMINAL
WILL DISPLAY "BOOTING FROM CS0........." AND "BOOT
COMPLETE".
5.3.1A.9 WHEN <EXEC> IS DISPLAYED, TYPE "install" AND <CR>.
5.3.1A.10 WHEN PROMPTED "DESTROY:",ENTER "Y".
5.3.1A.11 WHEN PROMPTED "DISK NAME", PRESS <CR>.
5.3.1A.12 VERIFY THAT THE INSTALLATION STARTS.
5.3.1A.13 WHEN COMPLETE AND <EXEC> IS DISPLAYED, CONTINUE ON TO
THE NEXT PARAGRAPH.
5.3.2 INSTALL OS
NOTE: WHEN INSTALLING A NEW OS RELEASE, IT WILL NOT BE NECESSARY TO REINSTALL
THE DIAGNOSTICS AGAIN. 5.3.2.1 INSTALL THE OS TAPE CARTRIDGE INTO THE TAPE DRIVE.
5.3.2.2 WHEN PROMPTED <EXEC>, TYPE "DE" AND <CR>.
5.3.2.3 WHEN PROMPTED <DEBUG>, TYPE "BO CS" AND <CR>.
5.3.2.4 WHEN PROMPTED "SYSTEM FILE:", DEPRESS THE <CR>.
5.3.2.5 VERIFY THAT THE SYSTEM LOADS FROM THE STREAMER AND
THAT THE TERMINAL DISPLAYS THE FOLLOWING:
******************************************************
* *
* BOOTING FROM CS0 *
* LOADING OPERATING SYSTEM *
* ............................................. *
* ............................................. *
* ............... *
* LOADING CONFIGURATION FILE *
* . *
* LOADING RAMDISK *
* ............................................. *
* ............................................. *
* ............... *
* EXECUTING *
* *
* *** INSTALLATION SYSTEM LOAD COMPLETE! *** *
* *
* THIS INSTALLATION SYSTEM WILL BE USED TO PERFOM *
* ONE OF THREE FUNCTIONS. ----------------------- *
* ----------------------------------------- SELET *
* THE DESIRED OPTION AND TYPE THE CORRESPONDING *
* LETTER FOLLOWED BY THE 'RETURN' KEY. *
* *
* A - CREATE DEFAULT PARTITIONS *
* *
* B - PRESERVE CURRENT PARTITIONS *
* *
* C - RESTORE LOADER TO WINCHESTER DISK *
* *
* D - INSTALL CONFIGURATION RECORD *
* *
* E - REDISPLAY THIS SCREEN *
* *
* <CTL-D>, 'shutdown' - REBOOT THE SYSTEM *
* *
* OPTION> *
******************************************************
5.3.2.6 WHEN PROMPTED <OPTION>, TYPE "d" AND <CR>.
5.3.2.7 WHEN PROMPTED "INSERT CONFIGURATION TAPE, PRES RETURN
.....", INSERT THE TAPE AND PRESS <CR>.
5.3.2.8 THE TAPE SHOULD RUN AND THEN THE DISPLAY SHOULD BE AS
FOLLOWS:
******************************************************
* CAUTION: FILES ON THIS TAPE ARE............ *
* ....................MATCH ORIGINAL OWNERS.*
* NUMBER OF FILES RESTORED: 1 *
* CONFIGURATION RECORD INFO (/sys/config.XXXX-90000 *
* USER SSN.........................XXXX-90000 *
* SYSTEM NAME......................010/SYSTEMS TEST *
* SYSTEM TYPE......................XXXX *
* " *
* " *
* " *
* MCS CONTROLLER...................YES *
* MTS CONTROLLER...................YES *
* WRITING NEW CONFIGURATION *
* *
* PROCEDURE COMPLETE. <CTL-D> 'shutdown' TO REBOOT *
* *
* OPTION> *
* *
******************************************************
5.3.2.9 WHEN PROMPTED "OPTION>", REMOVE THE CONFIGURATION
TAPE AND REINSERT THE OS TAPE.
5.3.2.10 WHEN THE OS TAPE HAS BEEN INSTALLED, TYPE "a" AND
<CR>.
5.3.2.11 THE TAPE SHOULD RUN AND THEN THE DISPLAY SHOULD BE AS
FOLLOWS:
******************************************************
* CREATING DEFAULT PARTITIONS.... *
* /dev/rwd0: *
* VOLUME ID: BFISD M A I XXXX *
* LAST REVISED ON DAY MONTH XX YEAR HH:MM:SS *
* DEVICE TYPE: CCCCCC *
* CLASS: 0 *
* CAPACITY: XXXXX *
* NUMBER OF CYLINDERS: XXX *
* NUMBER OF HEADS: X *
* NUMBER OF SECTORS PER TRACK: XX *
* NUMBER OF BYTES PER SECTOR: XXX *
* PARTITION :0 START:0 END:XXXXX LENGTH:XXXX *
* PARTITION :1 START:0 END:4095 LENGTH:406 *
* PARTITION :2 START:4096 END:8191 LENGTH:406 *
* PARTITION :3 START:8192 END:XXXXX LENGTH:XXXX *
* TRANSFERING BOOT PARTITION TO DISK.... *
* PROCEDURE COMPLETE. PLEASE RE-BOOT *
* (TYPE CTRL-D, SHUTDOWN, 'RETURN) *
******************************************************
5.3.2.12 WHEN PROMPTED "PROCEDURE COMPLETE. PLEASE REBOOT",
DEPRESS THE CONTROL AND D KEYS TOGETHER.
5.3.2.13 WHEN PROMPTED "SINGLE, MULTI OR SHUTDOWN", TYPE
"shutdown" AND <CR>.
5.3.2.14 REBOOT THE SYSTEM FROM WD0.
5.3.2.15 VERIFY THAT THE SYSTEM LOADS FROM WD0.
5.3.2.16 WHEN PROMPTED "UPDATE CLOCK", DEPRESS THE <CR>.
5.3.2.17 WHEN PROMPTED <ADMIN>, TYPE "osinstall cs" AND <CR>.
5.3.2.18 WHEN PROMPTED "THIS PROCEDURE WILL DESTROY ALL
PREVIOUS DATA ON ROOT PARTITION. PRESS RETURN TO
CONTINUE (ESCAPE TO ABORT...)", PRESS <CR>.
5.3.2.19 VERIFY THAT THE TERMINAL DISPLAYS THE FOLLOWING:
******************************************************
* *
* MAKING FILESYSTEM *
* MAKING FREEMAP *
* MAKING FDMAP WITH XXXX FDS *
* MAKING NEW FDS *
* XXXXX BLOCKS AVAILABLE, WRITING HEADER *
* *
* RESTORED /OUT/BIN *
* RESTORED /OUT/BIN/ADDNAME *
* RESTORED /OUT/BIN/ADMIN *
* . *
* . *
* . *
* RESTORED /OUT/UTIL *
* RESTORED /OUT/UTIL/F1/EOS.F *
* NUMBER OF FILES RESTORED = XXX *
* *
* EXECUTING PRODUCT SPECIFIC INSTALLATION ROUTIN... *
* *
* EXECUTION OF PRODUCT SPECIFIC INSTALLATION *
* ROUTINE COMPLETE *
* *
* REWINDING TAPE... *
* *
* PROCEDURE COMPLETE. PLEASE RE-BOOT *
* (TYPE CTRL-D, SHUTDOWN, 'RETURN) *
******************************************************
5.3.2.20 WHEN PROMPTED "PROCEDURE COMPLETE. PLEASE REBOOT",
DEPRESS THE CONTROL AND D KEYS TOGETHER.
5.3.2.21 WHEN PROMPTED "SINGLE, MULTI SHUTDOWN OR POWER DOWN",
TYPE "shutdown" AND <CR>.
5.3.2.22 REBOOT THE SYSTEM FROM WD0.
5.3.2.23 VERIFY THAT THE SYSTEM LOADS FROM WD0.
5.3.3 INSTALL OS PRODUCTS, TEST PROGRAMS & CONFIGURE
5.3.3.1 WHEN PROMPTED "UPDATE CLOCK", DEPRESS THE <CR>.
5.3.3.2 WHEN PROMPTED <ADMIN>, TYPE "install cs EUT EBS EXT
EBA" AND <CR>.
5.3.3.3 AT THE <ADMIN> PROMPT, TYPE "menu" AND <CR>.
5.3.3.4 WHEN THE INITIAL MENU IS DISPLAYED, TYPE "1" AND <CR>
TO SELECT THE UTILITIES MENU.
5.3.3.5 AT THE UTILITIES MENU, TYPE "1" AND <CR> TO SELECT THE
DIRECTORY MENU.
5.3.3.6 AT THE DIRECTORY MENU, TYPE "2" AND <CR> TO SELECT THE
"CREATE A DIRECTORY" PROGRAM.
5.3.3.7 WHEN PROMPTED "TYPE WORKING DIRECTORY", TYPE"/" AND
<CR>.
5.3.3.8 WHEN PROMPTED "TYPE NAME OF DIRECTORY TO CREATE", TYPE
"test" AND <CR>.
5.3.3.9 THE TERMINAL WILL DISPLAY "DIRECTORY CREATED".
5.3.3.10 WHEN PROMPTED "TYPE NAME OF DIRECTORY TO CREATE", TYPE
<CR> TO END. 5.3.3.11 AT THE DIRECTORY MENU, PRESS THE <CR> TO RETURN TO THE
UTILITY MENU.
5.3.3.12 AT THE UTILITY MENU, TYPE "5" AND <CR> TO SELECT THE
SAVE AND RESTORE MENU.
5.3.3.13 AT THE SAVE AND RESTORE UTILITIES MENU, TYPE "2" AND
<CR> TO SELECT THE RESTORE FROM CARTRIDGE PROGRAM.
5.3.3.14 WHEN THE DEFAULT CONDITIONS ARE DISPLAYED, PRESS THE
<CR> TO CONTINUE.
5.3.3.15 WHEN PROMPTED "INSERT TAPE NUMBER 1", INSERT THE TAPE
WITH THE TEST AND LABEL PROGRAMS AND PRESS THE <CR>.
5.3.3.16 WHEN PROMPTED "IS THIS THE CORRECT SAVE SET?", TYPE
"y" AND <CR>.
5.3.3.17 THE TAPE WILL BE COPPIED TO THE SYSTEM AND THEN A LIST
OF THE COPPIED FILES WILL BE DISPLAYED. PRESS THE <CR>
TO CONTINUE.
5.3.3.18 WHEN PROMPTED "INSERT TAPE NUMBER 1", INSERT THE TAPE
WITH THE RIFLE PROGRAM AND PRESS THE <CR>.
5.3.3.19 WHEN PROMPTED "IS THIS THE CORRECT SAVE SET?", TYPE
"y" AND <CR>.
5.3.3.20 WHEN THE WARNING MESSAGE IS DISPLAYED, PRESS <CR>.
5.3.3.21 THE TAPE WILL BE COPPIED TO THE SYSTEM AND WHEN
PROMPTED "PROGRAM COMPLETE. REMOVE CARTRIDGE", PRESS
THE <CR> TO CONTINUE.
5.3.3.22 AT THE MENU, PRESS THE CTL-IV KEY TO EXIT THE MENU
PROGRAM.
5.3.3.23 WHEN PROMPTED "ADMIN", DEPRESS THE CONTROL AND D KEYS
TOGETHER.
5.3.3.24 WHEN PROMPTED "SINGLE, MULTI OR SHUTDOWN", TYPE
"shutdown" AND <CR>.
5.3.3.25 REBOOT THE NSYSTEM FEOM WD0.
5.3.3.26 VERIFY THAT THE SYSTEM LOADS FROM WD0.
5.3.3.27 WHEN PROMPTED "UPDATE CLOCK", DEPRESS THE <CR>.
5.3.3.28 WHEN <ADMIN> IS DISPLAYED TYPE "init" AND <CR>.
5.3.3.29 WHEN THE MENU IS DISPLAYED, TYPE "2" AND <CR> TO
SELECT PHOENIX SYSTEMS.
5.3.3.30 WHEN PROMPTED TO ENTER THE NUMBER OF MEMORY BOARDS,
TYPE THE NUMBER OF MEMORY BOARDS CONFIGURED IN THAT
SYSTEM FOLLOWED BY A <CR>.
5.3.3.31 WHEN PROMPTED "ADMIN>",TYPE "configure" AND <CR>.
5.3.3.32 WHEN WARNING MESSAGE IS DISPLAYED, PRESS THE <CR>.
5.3.3.33 WHEN THE SYSTEM CONFIGURATION IS DISPLAYED, VERIFY
THAT TTY0 IS SET ON PORT 0.
5.3.3.34 FOLLOW THE MENU PROMPTS TO CONFIGURE PORT 1 AND PORTS
3 THROUGH 18 TO A EVDT TERMINAL WITH DEFAULT SETTINGS.
5.3.3.35 FOLLOW THE MENU PROMPTS TO CHANGE PORT 2 TO AN "lpm"
PRINTER WITH A DESIGNATION OF lp.
5.3.3.36 WHEN THE CONFIGURATION IS CORRECT, TYPE "7" AND <CR>.
5.3.3.37 WHEN <ADMIN> IS DISPLAYED, PRESS THE CONTROL AND THE D
KEYS TOGETHER.
5.3.3.38 WHEN PROMPTED "SINGLE, MULTI OR SHUTDOWN", TYPE
"shutdown" AND <CR>.
5.3.3.39 WHEN THE SYSTEM HAS SHUTDOWN, TURN OFF THE POWER.
5.3.3.40 REMOVE THE DISK DRIVE AND MARK IT AS A MASTER WITH
THE OS AND DIAGNOSTIC RELEASE NUMBERS ON IT.
5.4.1 CONFIGURE THE SYSTEM TO BOOT FROM FD0.
5.4.2 CONFIGURE THE DISK DRIVE TO BE TESTED AS DRIVE 1.
5.4.3 CONNECT THE BUS AND RADIAL CABLES FROM THE DISK DRIVE TO THE
CONTROLLER. USE THE CABLES THAT WILL BE SHIPPED WITH THE DISK
BEING TESTED.
5.4.4 TURN ON THE SYSTEM POWER.
5.4.5 INSTALL A #1 DIAGNOSTIC DISKETTE INTO THE FLOPPY DISK DRIVE.
5.4.6 THE TERMINAL WILL DISPLAY THE SYSTEM SELF-TEST AND THE FLOPPY
DRIVE WILL BEGIN TO READ AND THE TERMINAL WILL DISPLAY "BOOTING
FROM FD0............" AND "BOOT COMPLETE".
5.4.7 WHEN <EXEC> IS DISPLAYED, TYPE "LO DISK" AND <CR>.
5.4.8 WHEN THE PROGRAM IS LOADED AND THE <DISK> PROMPT APPEARS, TYPE
"WRITEOK" AND <CR>.
5.4.9 WHEN PROMPTED <DISK>, TYPE "UNIT 1" AND <CR>.
5.4.10 WHEN PROMPTED <DISK>, TYPE " RUNIN" AND <CR>.
5.4.11 THE TEST WILL START AND A SCROLLING ERROR LOG WILL DISPLAY.
CONTINUE THIS TEST FOR THE LENGTH OF TIME SPECIFIED IN SECTION
5.0 OF THIS PROCEDURE. THE UNITS UNDER TEST MUST RUN ERROR-FREE
FOR THIS PERIOD OF TIME.
5.5.1 CONFIGURE THE SYSTEM TO BOOT FROM FD0.
5.5.2 INSTALL THE FLOPPY DISK DRIVE TO BE TESTED. USE THE CABLE THAT
WILL BE SHIPPED WITH THE DRIVE UNDER TEST.
5.5.3 TURN ON THE SYSTEM POWER.
5.5.4 INSTALL A #1 DIAGNOSTIC DISKETTE INTO THE FLOPPY DISK DRIVE.
5.5.5 THE TERMINAL WILL DISPLAY THE SYSTEM SELF-TEST AND THE FLOPPY
DRIVE WILL BEGIN TO READ AND THE TERMINAL WILL DISPLAY "BOOTING
FROM FD0............" AND "BOOT COMPLETE".
5.5.6 WHEN <EXEC> IS DISPLAYED, TYPE "LO FLOPPY" AND <CR>.
5.5.7 WHEN THE PROGRAM IS LOADED AND THE FLOPPY DRIVE'S LED GOES OUT,
REPLACE THE DIAGNOSTIC DISKETTE WITH A FORMATTED BLANK DISKETTE
5.5.8 WHEN PROMPTED <FLOPPY>, TYPE "RUNIN" AND <CR>.
5.5.9 THE TEST WILL START AND A SCROLLING ERROR LOG WILL DISPLAY.
CONTINUE THIS TEST FOR THE LENGTH OF TIME SPECIFIED IN SECTION
5.0 OF THIS PROCEDURE. THE UNITS UNDER TEST MUST RUN ERROR-FREE
FOR THIS PERIOD OF TIME.
O S ERROR CODES
----------------1:Attempt to access beyond end of file. -2:An I/O error occurred. -3:EBADSECT -4:Program is too large to fit in memory. -5:File does not exist. -6:ENOSTREAM -7:Bad modes string in system-level open call. -8:No more file descriptors free in the system. -9:No more logical units are available to this process. -10:An operation has been requested on a closed logical unit. -11:ETOODEEP -12:ECANTCREATE -13:EMISSING -14:A bad file name has been given to the file system. -15:The file system on the specified device has the wrong format. -16:ENOTONLINE -17:Out of space on the file system specified. -18:An object file being executed has a bad format. -19:The requested operation requires a directory. -20:Some directory in the pathname does not exist. -21:Attempted to delete a non-empty directory. -22:The specified file is a directory. -23:An attempt was made to open a directory for writing. -24:No more mount table space is available. -25:The file specified is not a device file. -26:The directory or device is busy. -27:The specified device is not mounted. -28:No more swap space is available. -29:There are no more processes or the process does not exist. -30:The specified logical unit is not that of a file. -31:The file, directory or device is in use. -32:A bad device was specified. -33:A bad system call was made. -34:An odd address was given to 'raw' I/O. -35:An invalid byte count was given to 'raw' I/O. -36:Cannot addname across filesystems. -37:The specified file or directory already exists. -38:The current process has no children. -39:Trap instruction -40:The specified logical unit is not that of an eventcount. -41:The request requires a 'double' eventcount. -42:A bad logical unit number was specified. -43:No more eventcall slots are available. -44:The requestor does not have read permission. -45:The requestor does not have write permission. -46:There are temporarily no more pipe structures. -47:An attempt was made to write to a pipe with no one reading it. -48:Access permission denied. -49:An attempt was made to execute a file which has a bad header. -50:A negative file position was specified. -51:An attempt was made to map a file which has not been added. -52:ENOSD -53:The specified file is a remote file. -54:A ctrl-X intterupt occurred. -55:A bad mnemonic was encountered. -56:An attempt was made to access a bad keyed file. -57:ENOTTTYCMD -58:ETTYCMDVERSION -59:The directory is in use. -60:A seek error has occurred. -61:Not enough memory. -62:The requested operation has timed out. -63:Write protected. -64:A write error occurred formatting diskette. -65:File descriptor has maximum number of names. -66:Filesystem is mounted read-only. -67:No more record lock entries are available. -68:Waiting on the specified record would establish a deadlock. -69:Bad parameter. -70:The file is a special file system device. -71:Bad key. -72:Bad file system. -73:A bad index was given to the file system. -74:Data buffer too small. -75:Bad file type. -76:Attempt to access beyond beginning of file. -77:Key doesn't exist. -78:Duplicate key. -79:ENOCURR -80:ENOREC -81:EADDKEY -82:EDELKEY -83:Disk is already enabled. -84:Disk is not enabled. -85:End of tape. -86:Drive seek error or data transfer error. -87:Device minor number specified was a partition. -88:Bad argument passed to system. -89:Device off-line. -90:EFILEMARK -91:End of data has been reached. -92:EBADLENGTH -93:Printer buffer overflow has occurred. -94:Printer is out of paper. -95:Printer is off-line. -96:Async I/O is in progress. -97:No cartridge. -98:ERDERCON -99:Originally mounted diskette not found. -100:Disk was left mounted, override disabled. -101:No clist. -102:No disk in floppy disk drive. -103:Unknown printer mnemonic. -104:Duplicate directory. -105:Too many directories given. -106:Tty input buffer overflow. -107:Printer out of ribbon. -108:Printer I/O transmission error. -109:Not a buffered device. -110:The printer is busy. -111:Parity error -112:Attempt to execute an illegal instruction -113:Bpt/trace -114:Memory management error -115:Odd address error -116:Divide by zero error -117:Check instruction -118:Overflow condition caught -119:Privlege violation -120:Unknown trap -200:The requested function is not available. -201:A bad logical unit number was specified. -202:No more logcal units available for this process. -203:Bad parameter. -204:The file or device is not locked. -205:The file or device is locked. -206:The logical disk is not defined. -207:The file system mount table does not exist. -208:The requested operation requires a basic program file. -209:The program is in use. -210:The basic program file is too small. -211:Data buffer too small. -212:No basic program file has been loaded. -213:The file already exists. -214:A bad public programming logical unit was specified. -215:The requested file was not added to shared memory. -216:The file is addred. -217:The file has not been addred. -218:The specified file is not a disk file. -219:Bad date. -220:Bad time. -221:Bad time/date format. -223:The requested operation requires a size. -224:JAWAIT -225:A file system command has timed out. -226:A ctrl-X intterrupt occurred. -227:An attempt was made to reopen the console. -228:An attempt was made to restart an audit trail. -229:WRITEVIAINPUT -230:An attempt has been made to access a bad keyed file. -231:The requested operation requires a basic program file. -251:The specified printer is not defined. -252:The specified default printer is not defined. -253:BADDEFFILE -254:Bad order. -255:Bad number of copied. -256:The printer queue files do not exist. -257:File does not exist. -258:Printer form does not exist. -32767:Non-existent memory was specified for a system call. -32768:The current system call was terminated.
INITIAL AND DATE ALL TESTS PERFORMED. ENTER "N/A" FOR OPTIONS NOT CONFIGURED.
CPU SN __________ SSN __________ MSO/ORDER # __________
| PROCEDURE | TESTER'S |
TEST OR DESCRIPTION | PARA. # | INITIALS | DATE
==============================================================================
SET JUMPERS & ZERO-OHM PACKS | 2.- | |
& ALL ADDRESS SWITCHES | ALL | |
---------------------------------------------|-----------|-----------|--------
RECORD (VERIFY HI-POT) | 3.1 | |
---------------------------------------------|-----------|-----------|--------
POWERUP, SELFTEST & CONFIG | 3.2 | |
---------------------------------------------|-----------|-----------|--------
INSTALL TEST SSN ** MODULAR UNITS ONLY | 3.3 | |
---------------------------------------------|-----------|-----------|--------
INSTALL USER SSN ** MSO UNITS ONLY | 3.3 | |
---------------------------------------------|-----------|-----------|--------
INSTALL USER CONFIG RECORD ** MSO UNITS ONLY| 3.4 | |
---------------------------------------------|-----------|-----------|--------
VERIFY WD0 BOOT & CONFIGURE SYSTEM | 3.5 | |
---------------------------------------------|-----------|-----------|--------
PRINT LABEL | 3.6 | |
---------------------------------------------|-----------|-----------|--------
DIAGNOSTICS | 4.2 | |
---------------------------------------------|-----------|-----------|--------
MINIQ | 4.3 | |
---------------------------------------------|-----------|-----------|--------
FINAL TEST - SERIAL PORTS (test1) | 4.4.1 | |
---------------------------------------------|-----------|-----------|--------
FINAL TEST - PARALLEL PORT (test2) | 4.4.1 | |
---------------------------------------------|-----------|-----------|--------
FINAL TEST - MCS TAPE DRIVES (test3) | 4.4.2 | |
---------------------------------------------|-----------|-----------|--------
FINAL TEST - MTS TAPE DRIVES (test4) | 4.4.3 | |
---------------------------------------------|-----------|-----------|--------
FINAL TEST - LAN CONTROLLER (test5) | 4.4.4 | |
---------------------------------------------|-----------|-----------|--------
FINAL TEST - WD1 (test6) | 4.4.5 | |
---------------------------------------------|-----------|-----------|--------
CLEAR TEST PROGRAMS | 4.5 | |
---------------------------------------------|-----------|-----------|--------
DELETE CONFIG RECORD ** MODULAR UNITS ONLY | 4.6 | |
---------------------------------------------|-----------|-----------|--------
INSTALL FINAL SSN ** MODULAR UNITS ONLY | 4.7 | |
---------------------------------------------|-----------|-----------|--------
COMMENTS: