This  directory  contains  4  programs.  They  constitute  a  file
    transfer utility for 11m 3.2 between two machines that  each  have
    the full duplex driver. The SND program sends the file and the REC
    program  receives  it.  If  file transfers are not done too often,
    (and you don't want 3 programs  installed  and  1  active  at  all
    times)  then  you  can just Run the REC program on one end and the
    SND on the other (it does a get command  line  and  therefore  you
    need the /prm= patch to install or you must install the program).

    Alternatively,  if  you install three programs and run one all the
    time (its only 1/2k and stopped when not doing anything) the  SEND
    utility  will  perform  send data's to the TRNSFR program who will
    wake up the other end (the tran program runs  as  TRNSFR  on  both
    ends)  and  spawn the SENDER. Users can queue up send requests but
    the send program stops until the file(s) are transfered.  (SND  is
    thus installed as SENDER and REC is installed as RECEIV). 

    The  syntax  of  the  send command is: >send file1 file2 ... (file
    name must be 22 char or less) 

    Group protection and error recovery are included.  All  attributes
    of  the  file  are  transfered  and  a  contiguous  file  is  made
    contiguous on the other end. At 9600 baud, an effective rate of 17
    blocks per 20 seconds is realized. 

    The TRNSFR  program  runs  /pr:0  so  it  can  spawn  RECEIV  with
    uic=[1,1].  This may not be necessary but it works for now. RECEIV
    needs uic [1,1] so it can set ownership of files and have  access.
    A  spawned  program from a slaved task tends to get tt0 as its ti:
    and in order to set the UIC to [1,1] the receiver program needs to
    be installed when using the TRNSFR task. 

    The following is the startup we use to initialize the lines. (some
    of it may not be necessary but I'm not sure). 

SET /SLAVE=tt5:
SET /NOCRT=tt5:
SET /NOECHO=tt5:
SET /EBC=tt5:
SET /RPA=tt5:
SET /NOTYPEAHEAD=tt5:                  !do this to clear typeahead buffer
SET /TYPEAHEAD=tt5:                    !but we do want typeahead
SET /FDX=tt5:
SET /NOVFILL=TT5:
SET /HFILL=TT5:0
set /nowrap=tt5:
set /hht=tt5:

    If the 2 machines get out of sync, we use  the  following  command
    file. 
 

.IFACT RECEIV ABO RECEIV
.IFACT TRNSFR ABO TRNSFR
.IFACT SENDER ABO SENDER
.WAIT RECEIV
.WAIT TRNSFR
.WAIT SENDER
@[1,2]CM TT5
                .SETS TTY   P1                  <---- this is cm.cmd
		.ENABLE SUBSTITUTION
		SET /SLAVE='TTY':
		SET /NOCRT='TTY':
		SET /NOECHO='TTY':
		SET /EBC='TTY':
		SET /RPA='TTY':
		SET /NOTYPEAHEAD='TTY':
		SET /TYPEAHEAD='TTY':
		SET /FDX='TTY':
		SET /NOVFILL='TTY':
		SET /HFILL='TTY':0
		set /nowrap='TTY':
		set /hht='TTY':
		asn 'TTY':=cm00:/gbl
                asn 'TTY':=cm01:/gbl            <--- down to here
rem trnsfr
rem sender
rem receiv
ins $tran/task=trnsfr
ins $snd/task=sender
ins $rec/task=receiv
run trnsfr 20t